00196932-02 SM S-Feeder Repair DE EN multilang - 第79页

1 Introduction 1.1.1 Conventions for the use of safety instructions 1.1 Safety Instructions SIPLACE S-Feeder Repair SIPLACE S-Förderer Reparatur 79 1 1 I n t r o d u c t io n Introduction This manual describes the operat…

100%1 / 144
78 SIPLACE S-Feeder Repair SIPLACE S-Förderer Reparatur
9.3 Following tasks 123
10 3x8mm S-Förderer - Foil disposal unit 125
10.1 Disassembling the foil disposal unit 125
10.2 Dismantling of DC gear motor 129
10.3 Assembly of DC gear motor 130
10.4 Assembly Foil disposal unit 131
11 3x8mm S-Feeder - Worm gear drive 135
11.1 Removal of worm gear drive 135
11.2 Design of worm gear drive 140
1 Introduction
1.1.1 Conventions for the use of safety instructions 1.1 Safety Instructions
SIPLACE S-Feeder Repair SIPLACE S-Förderer Reparatur 79
1
1 Introduction
Introduction
This manual describes the operation of the SIPLACE ® S-Feeder Motor Tester and the associated re
-
pairs to SIPLACE S-feeders.
1.1
1.1 Safety Instructions
Safety Instructions
1.1.1
1.1.1 Conventions for the use of safety instructions
Conventions for the use of safety instructions
This manual contains notes that must be observed to guarantee your personal safety and to avoid dam
-
age to equipment. These notes are highlighted by warning triangles and are indicated as follows accord
-
ing to the level of risk:
1.1.2
1.1.2 Safety Instructions
Safety Instructions
The SIPLACE placement machines are powered by line voltage.
Parts of the system therefore conduct dangerous electricity!This electricity is present at certain assem
-
blies inside the machine even while the master switch is turned off.
Incorrect use of the machine or touching live machine parts can cause fatal or severe injuries and con
-
siderable damage to the equipment.
After you have properly shut down the operating system and before you perform any work on the ma
-
DANGER
Nonobservance of these safety instructions may cause injury to personnel and damage to the
machine!
► Please observe the safety instructions in the user manual of the relevant machine for all
work!
DANGER
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable dam
-
age to property will occur if this hazard warning is not observed.
WARNING
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable dam
-
age to equipment may occur if these warning instructions are not followed.
CAUTION
Definition
For the purposes of this manual, this indicates that minor injuries or damage to property may
occur if this caution is not observed.
NOTICE
Definition
For the purposes of this manual, this note provides information about the product or indicates
a part of the manual that requires particular attention.
CAUTION
Observe the safety instructions!
The safety instructions in the chapters "Operational Safety" of the Operating Manual and Ser
-
vice Manual take precedence.
1 Introduction
1.1 Safety Instructions 1.1.2 Safety Instructions
80 SIPLACE S-Feeder Repair SIPLACE S-Förderer Reparatur
chine, make sure the has been turned off at the main switch and is isolated from the line supply. In ad
-
dition, the compressed air supply must be turned off at the main valve of the compressed air unit in the
machine base and the compressed air lines must be bled by actuating the needle valve at the com
-
pressed air unit.
Danger: persons wearing a heart pacemaker are not permitted to work near linear motors, as described
in detail in the User Manual and the Service Manual, Chapter "Special Safety Instructions when working
in vicinity of powerful magnetic fields" .
Observe the applicable accident prevention regulations, DIN standards and special safety regulations
applicable for your country at all times.
Carefully read and observe the instructions about residual voltage in the Chapter "Operational Safety".
Also observe the ESD regulations in the Chapter "Operational Safety" of the operating manual.
Before performing any service or refitting work on the machine, secure it to prevent unauthorized use,
as described in the Chapter "Locking the Machine...".
There is an additional, higher risk of accident when working with the SITEST program.
The SITEST program may therefore only be started by specially authorized and trained
Put the tape feeder module on a stable, flat (!) surface, once it has been removed from the packaging.
Make sure that pressure is not applied to the sides, until the module is lying totally flat on an even sur
-
face. Otherwise, this could lead to malfunctions or irreparable damage to the feeder module, making re
-
adjustment work or even replacement necessary.
Make sure that the tape feeder module is not unintentionally trapped or clamped (e.g. in vices), otherwise
it could be squeezed or bent etc. If you need help, organize an assistant to hold it.
1.1.2.1
1.1.2.1 Definitions
Definitions
1.1.2.2
1.1.2.2 ESD Safety
ESD Safety
CAUTION
Avoid errors!
This message draws the operator's attention to possible sources of error which should be
avoided during work.
NOTICE
Useful tips!
This message draws the operator's attention to useful information which will make work easier
and help you optimize efficiency.
CAUTION
Always observe!
Warnings such as these draw the operator's attention to instructions or messages which must
be observed. Nonobservance causes a considerable risk of damage to the equipment and/or
injuries to the operator.
CAUTION
Observe the ESD regulations!
Pay attention to feeder module ESD safety:
Before you open the side cover, make sure you are wearing the ESD protection wristband, to
prevent damage to the highly sensitive boards inside the feeder module.