JM-50_OPE - 第7页
v 为了安全使用 JM -50 的注意事项 注意 1. 为防止人身受伤， 请勿在拆下安全 盖（安全罩） 、安全装置等状 态下运行。 2. 为防止人身受伤， 请务必小心，以 免头发、衣服 等被卷入传送带 链。 此外，请勿戴手 套。 3. 为防止人身受伤， 维护时（注油、 调整、日常检 修），请切断电 源。 4. 为防止人身受伤， 请在电源线上使 用漏电断路器 。 < 安全盖（安全罩） > 1 . 开关安全盖（安全罩） 时请注意…
iv
各使用环节中的注意事项
使用环境
1. 为防止因误动作而引起的事故，请勿在受高频焊机等干扰源（电磁波）影响的环境下使用。
2. 为防止因误动作而引起的事故，请勿在超过使用电源电压±10％的情况下使用。
3. 为防止因误动作而引起的事故，请在 0.5±0.05MPa 的供气压力下使用。
4. 为了安全使用，请在下述环境下使用。
运行的环境条件 温度 ：10℃～35℃
湿度 ：50％RH 以下 (无冷凝)
标高 ：1,000m 以下
5. 为防止电气部件破损引起的事故，从冷处将机器突然移动到暖处时，有时会结露，因此，请在完全
无需担心水滴后再接通电源。
6. 为防止电气部件破损而引起的事故，打雷时请停止使用，并拔出电源插头。
注意
v
为了安全使用
JM-50
的注意事项
注意
1.
为防止人身受伤，请勿在拆下安全盖（安全罩）、安全装置等状态下运行。
2. 为防止人身受伤，请务必小心，以免头发、衣服等被卷入传送带链。
此外，请勿戴手套。
3. 为防止人身受伤，维护时（注油、调整、日常检修），请切断电源。
4. 为防止人身受伤，请在电源线上使用漏电断路器。
<
安全盖（安全罩）
>
1. 开关安全盖（安全罩）时请注意下列事项。
・打开安全盖（安全罩）时要把盖（罩）向上开足直到面向左侧的锁定臂处于“上
锁”状态后，再放开手。
没有上锁就放开手时，盖（罩）有落下来的危险。
・关闭盖（罩）子时先解开锁，再关闭盖（罩）子。
（请注意，解开锁时不要使盖（罩）子落下来导致受伤。）
・不要过渡增加盖（罩）子、手把等的负荷。
・如果 Head 单元位于主机装置后面，开关后侧安全盖（安全罩）时，可能会接触
到 X 轴单元。这时，请将 Head 单元移动到主机装置前面，再进行后侧安全盖
（安全罩）的开关。
注意
1.
本装置的操作系统采用
Windows 7
（包括以太网通信功能）。
除安装提供的用于本装置的软件之外，加装其他软件，不保证正常运行。
对 SSD 内装入的文件进行转移、重命名、文件或文件夹的压缩、复制，也同样
不保证正常运行，敬请谅解。
●万一出现此种情况，可能需要更换新的
SSD
、丢失数据，务请格外注意。
注意
为保护操作系统，使用了
Enhanced Write Filter(EWF)
组件，进行了
C
盘
ROM
化。
1. 请勿在 C 盘保存文件。
把文件保存在 ROM 化后的 C 盘，会仿真占用主存储器。
因而，把文件存在 C 盘里时，会增加主存储器的使用量，压迫系统。
反复保存后可能造成内存不足，显示系统错误，可能需要重启本设备。
2. 需要修改操作系统的信息时，必须进行 C 盘的更新操作。
操作方法请参见使用说明书「1-10 更新 C 盘的操作」。
需要修改操作系统信息的操作是指下列事项：
・JM-50 系统软件的版本升级
・添加打印机
・设置网络（IP 地址、工作组等）
・添加用户
・变更资源管理器的设置
●要变更操作系统信息时，在执行 C 盘的更新操作后，需要重启一次本装置。
注意
本装置的
D
盘可用于安装软件或保存数据，但容量有限。
1：请确保 D 盘的可用空间。
D 盘的可用空间请确保 500MB 以上。
可用空间不足 500MB 时，请删除无用的文件(旧版本的主机软件、Log 文件、无
用的生产程序等），以确保可用空间。
●在可用空间不足的状态下使用时，可能发生应用软件错误或文件 I/O 错误，导致软
件运行不稳定，无法进行正常的动作。
注意
1.
本装置在
ATX
电源中使用了电池，以保护停电时的生产程序等。
为防止 ATX 内置电池老化，请勿在非通电状态下将本装置放置 6 个月以上。
●本装置以主断路器及总开关
ON
的状态为通电状态。
为了安全使用机器
目 录
第 1 章 装置概要 ············································································································· 1-1
1-1 本装置概要 ············································································································ 1-1
1-1-1 前言 ················································································································1-1
1-1-2 关于标记 ··········································································································1-1
1-1-3 本书的构成 ·······································································································1-1
1-1-4 缩写的说明 ·······································································································1-2
1-1-5 本装置的构成 ····································································································1-3
1-2 机械规格 ··············································································································· 1-5
1-2-1 机械尺寸与重量·································································································1-5
1-3 基本操作 ··············································································································· 1-6
1-3-1 画面构成示例 ····································································································1-6
1-3-2 显示装置及输入装置 ··························································································1-7
1-3-3 操作方法 ··········································································································1-9
1-3-4 菜单、功能按钮······························································································· 1-14
第 2 章 生产 ··················································································································· 2-1
2-1 流程图 ·················································································································· 2-1
2-2 设备的启动和退出 ··································································································· 2-2
2-2-1 设备的启动 ·······································································································2-2
2-2-2 设备的退出方法·································································································2-4
2-2-3 预热 ················································································································2-5
2-3 生产准备 ··············································································································· 2-8
2-3-1 设置基板 ··········································································································2-8
2-4 生产画面 ··············································································································· 2-9
2-4-1 生产画面的启动·································································································2-9
2-4-2 生产辅助 ········································································································ 2-10
2-4-3 支援准备 ········································································································
2-10
2-4-4 确认贴片点 ····································································································· 2-24
第 3 章 维护 ··················································································································· 3-1
3-1 日常检查项目一览 ··································································································· 3-1
3-1-1 气压、排水瓶 ····································································································3-3
3-1-2 真空发生器压力·································································································3-4
3-1-3 管道及接头 ·······································································································3-5
3-1-4 各单元气缸 ·······································································································3-5
3-1-5 空气过滤器（LNC120-8 Head） ·············································································3-6
3-1-6 传送带 ·············································································································3-7
3-1-7 传送滑轮 ，输送辊 ····························································································3-9
3-1-8 支撑板 ·············································································································3-9
3-2 清扫 ··················································································································· 3-10
3-2-1 XY 轴直动单元 ································································································· 3-10
3-2-2 各种传送传感器······························································································· 3-11
3-2-3 CAL 块 ··········································································································· 3-12
3-2-4 激光校准传感器······························································································· 3-13
3-2-5 高度测量装置(HMS) ·························································································· 3-14
3-2-6 吸嘴 ·············································································································· 3-15
3-2-7 吸嘴外圈 ········································································································ 3-17
3-2-8 ATC 单元 ········································································································ 3-18
3-2-9 供料器台架 ····································································································· 3-18
3-2-10 统一更换台车 ································································································ 3-19