Service Manual SIPLACE SmartFeeder - 第151页
7 Repairs to SmartFeeder 8 mm X / Xi 7.15 Handle with control panel Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 151 7.15 Handle with control panel 7.15.1 Handle assembly…
7 Repairs to SmartFeeder 8 mm X / Xi
7.14 Leaf spring
150 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
7.14 Leaf spring
Required spare part
Fig.48: Leaf spring
Feeder module Item no. Designation
SmartFeeder 8mmX
SmartFeeder 8 mm Xi
03071618-xx Leaf spring tape infeed /X2x8 PT V1
Tools required
●
Phillips screwdriver 0.6Nm
●
TORX screwdriver 0.6Nm, size T8
●
Flat or universal pliers
7.14.1 Replacing the leaf spring
► Carefully place the feeder module with the left
side down on a stable, level and clean surface.
► Remove the right side cover (see 7.3.3 "Remov-
ing the right side cover" [}103]).
► Pull the leaf spring up and out of the feeder mod-
ule.
► Fit the new leaf spring into the feeder module as
shown.
► Make sure that the end of the leaf spring can
move freely downwards.
► Fasten the right side cover (see7.3.4 "Fitting the
right side cover" [}104] ).
7 Repairs to SmartFeeder 8 mm X / Xi
7.15 Handle with control panel
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 151
7.15 Handle with control panel
7.15.1 Handle assembly
The handle assembly can not be replaced and is not available as a spare part.
7.15.2 Control Panel Assembly
Required spare part
Fig.49: Board assy. control panel (top), control panel assy. (bottom)
Fig.50: Cable control panel
Feeder module Item no. Designation
SmartFeeder 8mm X
SmartFeeder 8 mm Xi
03104269-xx Board assy. control panel X8Smart
03102428 -xx Control panel assy. X8Smart
03063592-xx Cable control panel X2x8
Tools required
●
Phillips screwdriver 0.9Nm
●
TORX screwdriver size T8, 0.6Nm
●
Tweezers or small screwdriver
7 Repairs to SmartFeeder 8 mm X / Xi
7.15 Handle with control panel
152 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
7.15.2.1 Removing the Control Panel and Board
► Carefully place the feeder module with the right
side down on a stable, level and clean surface.
► Remove the left side cover (see 7.3.1 "Removing
the Left Side Cover" [}102]).
► Loosen the lock(1) in the position "unlocked".
► Open the two marked TORX screws(2), with
which the cap on the foil stuffing unit is fixed.
► Carefully lift the cap on the foil stuffing unit(3) a
little from the base of the feeder module. Make
sure that the flat ribbon cable is still fastened to
the control panel board.
► Pull the control panel(4) out of the guidance, to-
gether with the board(5)
.
► Open the bracket on the flat ribbon cable connec-
tion(6)
at the board.
► Pull the flat ribbon cable(7) out of the flat ribbon
cable connection.
► Pull the flat ribbon cable out of the foil stuffing
unit cap.