Service Manual SIPLACE SmartFeeder - 第165页

7 Repairs to SmartFeeder 8 mm X / Xi 7.17 Foil container Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 165 ► Open the connection X202 on the control board. ► Remove the fl…

100%1 / 246
7 Repairs to SmartFeeder 8 mm X / Xi
7.17 Foil container
164 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
► Remove the rear sliding guide (see 7.2.1 "Re-
moving the Sliding Guide" [}100]).
► Carefully place the feeder module on its right
side.
► Remove the left side cover (see 7.3.1 "Removing
the Left Side Cover" [}102]).
► Loosen the screw marked B (M 2.5x5) with a
Phillips screwdriver.
► Loosen the 3 screws marked A (RF 2.5x6) with a
TORX screwdriver.
ð The lower stiffener (1) also loosened will be
pulled off the foil box at a later time.
► Remove the TORX screw (RF 2.5x7.5) fastening
the filler piece for the splice sensor.
► Remove the two TORX screws (RF 2.5x7.5)
fastening the foil box to the empty tape duct.
► Remove the two TORX screw fastening the foil
box (1)
to the foil stripping unit (2).
7 Repairs to SmartFeeder 8 mm X / Xi
7.17 Foil container
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 165
► Open the connection X202 on the control board.
► Remove the flat ribbon cable leading to the con-
trol panel.
► Reach between the foil box and the righthand
side cover with the finger of your right hand.(1)
► Use your left hand to carefully lift the top stiffener
together with the foil stripping unit.(2a)
► At the same time, press the foil box down with
the thumb of your right hand.(2b)
The connection between the foil stripping unit and the
foil box should now open.(3)
If the connection does not open:
► Move the rocker, to separate the tamp wheels of
the foil rocker from the rocker.
► Pull the foil stripping unit and the foil box carefully
apart.
► Observe the following instructions.
When pulling these apart, take care that the marked
areas as soon as the foil box has separated from the
foil stripping unit at (1)
.
► Make sure that the empty tape duct slides out of
the upper stiffener.(2)
► Make sure that the bottom stiffener is released
from the foil stripping unit.(3)
7 Repairs to SmartFeeder 8 mm X / Xi
7.17 Foil container
166 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
► Pull the bottom stiffener off the foil box.
► Remove the leaf spring from the righthand side of
the foil box.
► Remove the control panel from the handle (see
7.15.2.1
"Removing the Control Panel and
Board" [}152]).
► Remove the individual parts from the handle (see
7.15.3.1
"Removing individual parts from the
handle" [}155]).
► Remove the rocker (see 7.9.1.1 "Removing the
rocker assembly" [}137]).
 NOTICE!
Keep the parts removed from the foil box
safe. You will need to fit these parts onto the
new foil box.
.
7.17.1.2 Fitting the foil box
► Fasten the rocker (see 7.9.1.2 "Fitting the rocker
assembly" [}137]).
► Fasten the individual parts of the handle (see
7.15.3.2
"Fitting individual parts to the
handle" [}156]).
► Fasten the control panel to the handle (see
7.15.2.2
"Fitting the Control Panel and
Board" [}153]).
► Insert the leaf spring into the righthand side of the
foil box.