Service Manual SIPLACE SmartFeeder - 第170页

7 Repairs to SmartFeeder 8 mm X / Xi 7.17 Foil container 170 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

100%1 / 246
7 Repairs to SmartFeeder 8 mm X / Xi
7.17 Foil container
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 169
► Fasten the bottom stiffener with the three screws
marked with A
(RF-SN75-2.5 x 6-9.8, 03033796-
xx).
Use a TORX screwdriver, 0.6 Nm, size T8.
► Fasten the screw marked with B (SN 213307-H-
M2.5 x 5-A2-70, 03071822-xx).
Use a Phillips screwdriver.
► Fasten the left side cover (see 7.3.2 "Fitting the
left side cover" [}102]).
► Carefully place the feeder module on its right
side.
► Fasten the back slide guide (see 7.2.2 "Fitting the
Sliding Guide" [}100]).
► Slightly lift the right side cover at the back.
► Insert the shaft (2).
► From above, fit the flap (1) vertically onto the
shaft.
► Slightly lift the right side cover at the back.
► Push the foil box sheet from behind into the
feeder module.
Align the foil box sheet over the flap shaft so that
the label can be fully seen.
► Carefully place the feeder module with the left
side down on a stable, level and clean surface.
► Fasten the with the screws marked A.
Use a TORX screwdriver 0.6 Nm, size T8.
► Fasten the screw marked with B.
Use a Phillips screwdriver.
7 Repairs to SmartFeeder 8 mm X / Xi
7.17 Foil container
170 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
8 Repairs to SmartFeeder 2x8 mm X / Xi
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 171
8 Repairs to SmartFeeder 2x8 mm X / Xi
Feeder module Item no. Description
SmartFeeder 2x8mmX 00141269-xx SIPLACE SmartFeeder 2x8 mm X
00141289-xx SIPLACE SmartFeeder 2x8mm X splice sensor
SmartFeeder 2x8 mm X 00141479-03 SIPLACE SmartFeeder 2x8mm Xi
00141499-03 SIPLACE SmartFeeder 2x8mm Xi splice
Notes about SmartFeeder Xi
The SmartFeederXi feeder modules support high infeed speeds for maximum utilization of the
machine placement capacity with the SIPLACE SpeedStar CP20P2 placement head.
The corrugated slide on the back of the SmartFeeder is a clear identifying feature of the Smart-
Feeder Xi.
SIPLACE Pro shows the SmartFeederXi as a SmartFeederX. If a CP20P2 head is used in the
setup, SIPLACE Pro automatically assumes that a SmartFeederXi is being used. The maximum
speed of a SmartFeederXi depends on the placement head which uses this feeder module.
The station software also shows a SmartFeederXi as a SmartFeederX. If a faster SmartFeederXi
is needed for performance purposes (machine with CP20P2 head), although a slower Smart-
FeederX is configured, the feeder LED will flash briefly, to signal the status "Not fast enough". The
station software will mark this feeder orange with the status "Too slow".
The SmartFeeder 2x8mmXi feeder module can be operated at any machine which can already
accommodate the SmartFeeder 2x8mmX. The SmartFeeder 2x8mmXi can also be operated with
older station software versions 7xx.x.
For more information about introducing the SmartFeederXi, refer to the technical information "In-
troducing the SmartFeeder modules Xi" (German [TI2018-09D14], English [TI201809E14]).