Service Manual SIPLACE SmartFeeder - 第205页

8 Repairs to SmartFeeder 2x8 mm X / Xi 8.8 Drives Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 205 8.8.2 Shifted gear for tape drive NOTICE Spare parts kit Due to the pot…

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.8 Drives

204 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

8.8.1.2 Fitting the hybrid stepping motor assembly

NOTICE

The installation procedure is the same for the left and right lane

This section describes the installation of the hybrid stepping motor on the left side (lane 1).

The installation procedure for the hybrid stepping motor on the right side (lane 2) is the

same, except that it is laterally reversed.

Fig.63: Overview of connections on the control board

1. Tape drive left lane (lane 1) 3. Foil drive left lane (lane 1)

2. Tape drive right lane (lane 2) 4. Foil drive right lane (lane 2)

► Place the hybrid stepping motor in position and run the cable through the housing.

► Fit the gauge (1) for the tape motor.

► Use the two Phillips screws marked in the diagram to fasten the motor to 0.9Nm.

► Remove the gauge.

► Plug the motor cable connector into the relevant connection on the control board e.g. for the

foil drive of the left lane (lane 1).(2)

Select the connection which matches the motor from the "Overview of connections on the

control board" shown above.

► Refit the shifted gear (see 8.8.2.2 "Fitting the shifted gear 1 left / right tape" [}206]).

► Fasten the left side covers (see 8.3.2 "Fitting the Left Side Cover" [}175])

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.8 Drives

Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 205

8.8.2 Shifted gear for tape drive

NOTICE

Spare parts kit

Due to the potential wear of plastic toothed wheels, it is recommended that, when you find it

necessary to replace one shifted gear or toothed wheel, you also replace the other one.

For this purpose, we recommend the spare parts kit "ETP gear set tape X

2x8mm“ [03095484-xx], which contains both toothed wheels with washers and circlips.

Spare parts required

Fig.64: Spare parts kit "ETP gear set tape X 2x8mm" [03095484-xx]

The spare parts provided in the gear set are listed in the following table:

Feeder mod-

ule

Position Number Item no. Designation

SmartFeeder

2x8mmX

SmartFeeder

2x8 mm Xi

1 03095484-xx ETP drive unit tape X 2x8mm

1 1 03070908-xx Shifted gear 1 tape PA /X2x8

2 1 03070911-xx Toothed wheel 4 tape PA /X2x8

3 2 03083028-xx DIN 988-3x6x0.1-1.4310 (washer)

4 2 00305726-xx DIN 471-3x0.4-C67 (circlip)

5 1 03079902-xx Threaded axis toothed wheel 4 tape /

X2x8

In the SmartFeeder 2x8mmX, the toothed wheels for the shifted gear tape drive are fitted in differ-

ent ways.

The drive for the left lane is fitted with the "toothed wheel 4 tape PA /X2x8“ [03070911-xx] with the

"threaded axis toothed wheel 4 tape / X2x8" [03079902-xx]. The "shifted gear 1 tape PA /

X2x8" [03070908-xx], and the "toothed wheel 4 tape PA /X2x8" for the right lane are fitted with

washer and circlip.

The spare parts kit "ETP gear set tape X 2x8mm" [03095484-xx] contains all the parts in the follow-

ing table, in the quantities listed.

Tools required

●

Circlip pliers for outer rings 3-10 mm

●

Allen key 0.35Nm

●

Tweezers

8 Repairs to SmartFeeder 2x8 mm X / Xi

8.8 Drives

206 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

8.8.2.1 Removing the shifted gear 1 tape left/right

► Place the feeder on a stable, level and clean sur-

face.

► Remove the left or right side covers (see 8.3.1

"Removing the Left Side Cover" [}174], 8.3.3

"Removing the Right Side Cover" [}175]).

► Remove the circlip and the washer.(1)

► Remove the toothed wheel.

► Clean the bearing shaft and surroundings.(2)

8.8.2.2 Fitting the shifted gear 1 left / right tape

► Place a small grease film on the shaft (Poly-

lubGLY801).

► Fit the new toothed wheel.(1)

► Fit the washer and circlip(1).

► Lightly grease the circlip.

► Lightly grease between the toothed wheel and

gear motor.

► Fasten the left or right side cover (see 8.3.2 "Fit-

ting the Left Side Cover" [}175], 8.3.4 "Fitting the

Right Side Cover" [}176]).

8.8.2.3 Removing the Toothed Wheel 4 Tape Left

► Place the feeder on a stable, level and clean sur-

face.

► Remove the left and right side covers as appro-

priate . (See 8.3.1

"Removing the Left Side

Cover" [}174], 8.3.3 "Removing the Right Side

Cover" [}175])

► Remove the gear stage 1 tape PA X2x8mm. (See

8.8.2.1

"Removing the shifted gear 1 tape left/

right" [}206])

► Loosen and remove the screw(1).

► Remove the toothed wheel(2).

► Clean the bearing shaft and surroundings(3).