Service Manual SIPLACE SmartFeeder - 第226页

8 Repairs to SmartFeeder 2x8 mm X / Xi 8.10 Rocker 226 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 8.10.2 Replacing the individual parts of the rocker Spare parts requir…

100%1 / 246
8 Repairs to SmartFeeder 2x8 mm X / Xi
8.10 Rocker
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 225
8.10.1.1 Removing the Rocker Complete
► Place the feeder module with the left side down
on a stable, level and clean surface.
► Remove the right side cover (see 8.3.3 "Remov-
ing the Right Side Cover" [}175]).
► Remove the pressure springs.(1)
► Screw off the bearing shaft and remove the
rocker.(2)
► Where necessary, unscrew and remove the bear-
ing shaft and then remove the other rocker(3)
.
8.10.1.2 Fitting the rocker
► Refit the left rocker.
► Insert the right-hand rocker again.
► Reinsert the pressure springs.
► Fit the right side cover (see 8.3.4 "Fitting the Right Side Cover" [}176]).
8 Repairs to SmartFeeder 2x8 mm X / Xi
8.10 Rocker
226 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020
8.10.2 Replacing the individual parts of the rocker
Spare parts required
Fig.71: Rocker, tamp wheel and bearing shaft
Feeder module Item no. Designation
SmartFeeder 2x8mmX
SmartFeeder 2x8 mm Xi
03041735-xx Rocker with holder/foil disposal X8
03041017-xx Tamp wheel /rocker X8
03042321-xx Bearing shaft for rocker /X8
Tools required
●
Flat-bladed screwdriver
●
Tweezers
8.10.2.1 Removing the tamp wheel and bearing shaft
► Place the feeder on a stable, level and clean sur-
face.
► Remove the rocker as described in 8.10.1.1 "Re-
moving the Rocker Complete" [}225].
► Screw off the bearing shaft(1) and remove the
tamp wheel.(2)
8.10.2.2 Fitting the tamp wheel and bearing shaft
► Insert the tamp wheel into the rocker.(1)
► Insert the bearing shaft through the hole in the
rocker, through the tamp wheel and then screw it
in place.(2)
► Fasten the rocker as described in section
8.10.1.2
"Fitting the rocker" [}225].
8 Repairs to SmartFeeder 2x8 mm X / Xi
8.11 Knurled Tamp Wheel
Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 227
8.11 Knurled Tamp Wheel
Spare part required
Fig.72: Knurled tamp wheel
Feeder module Item no. Designation
SmartFeeder 2x8mmX
SmartFeeder 2x8mmXi
03061111Sxx Knurled tamp wheel
03083028-xx DIN 988-3x6x0.1-1.4310 (washer)
00305726-xx DIN 471-3x0.4-C67 (circlip)
03003122-xx Compensating disk /DI3.1
Tools required
●
TORX screwdriver 0.6Nm, size T8
●
Phillips screwdriver
●
Flat-bladed screwdriver
●
Tweezers
●
Circlip pliers for outer rings 3-10 mm