Service Manual SIPLACE SmartFeeder.pdf - 第77页

6 Repairs to SmartFeeder 4 mm X / Xi 6.15 Handle with control panel Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 77 6.15.2.2 Fitting the Control Panel and Board ► If this…

6 Repairs to SmartFeeder 4 mm X / Xi

6.15 Handle with control panel

76 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

6.15.2.1 Removing the Control Panel and Board

► Carefully place the feeder module with the right

side down on a stable, level and clean surface.

► Remove the left side cover (see 6.3.1 "Removing

the Left Side Cover" [}30]).

► Loosen the lock(1) in the position "unlocked".

► Open the two marked TORX screws(2), with

which the cap on the foil stuffing unit is fixed.

► Carefully lift the cap on the foil stuffing unit(3) a

little from the base of the feeder module. Make

sure that the flat ribbon cable is still fastened to

the control panel board.

► Pull the control panel(4) out of the guidance, to-

gether with the board(5)

► Open the bracket on the flat ribbon cable connec-

tion(6)

at the board.

► Pull the flat ribbon cable(7) out of the flat ribbon

cable connection.

► Pull the flat ribbon cable out of the foil stuffing

unit cap.

6 Repairs to SmartFeeder 4 mm X / Xi

6.15 Handle with control panel

Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020 77

6.15.2.2 Fitting the Control Panel and Board

► If this is not open, swing the bracket on the flat rib-

bon connection(2)

on the board upwards.

► Push the flat ribbon cable(1) through the foil stuff-

ing unit cap, as shown, with the blue side pointing

upwards.

► Push the flat ribbon cable(1), with the blue side

pointing upwards, further into the flat ribbon cable

connection(2)

, on the board.

► Make sure that the flat ribbon cable contacts lie

against the contacts on the connection.

► Swing the bracket on the flat ribbon connection

down(2)

► Insert the control panel(3) with the marked pins

into the marked holes(4)

on the board.

► Push the control panel(3) together with the

board(4)

sideways into the feeder module guid-

ance provided.

Make sure that the flat ribbon cable is not pinched

or pulled out of the connection on the board.

► Carefully life the cap on the foil stuffing unit(5) into

the position shown on the feeder module base.

Make sure that the flat ribbon cable hangs out of

the cap as shown.

► Fasten the cap on the foil stuffing unit at the

marked points(6)

with 2 screws. Use a size 8

TORX screwdriver and 0.6 Nm for this.

► Make sure that the lock(7) on the feeder module

moves easily and that no components are trapped

or pinched.

► Fasten the left side cover (see 6.3.2 "Fitting the

Left Side Cover" [}30]).

6 Repairs to SmartFeeder 4 mm X / Xi

6.15 Handle with control panel

78 Service Manual SIPLACE SmartFeeder 4 - 8 mm X / Xi SIPLACE SmartFeeder 2 x 8 mm X / Xi 11/2020

6.15.3 Individual parts on the handle

Required spare parts

Fig.23: Individual parts on the handle SmartFeeder 4 mm X

NOTICE