88192278-01-19 Installation Master - 第115页
PRINTER PREPARATION PRINTER HEIGHT AND LEVELLING Chapter Issue 15, May 20 Installation Manual 4.13 PRINTER HEIGHT AND LEVELLING Leg Spacers (Camera Linear Drive Printer Only) The mounting feet on the camera linear drive …
PRINTER PREPARATION
TRANSIT BRACKETS AND SCREWS REMOVAL
4.12 Installation Manual Chapter Issue 15, May 20
Camera Transit
Screws (Linear
Drive)
1. Loosen the lock nut that secures the transit screw to the camera Y plate.
2. Remove the transit screw that secures the camera Y plate to the camera Y
linear bearing ensuring that the lock nut and crinkle washer are removed
with the transit screw.
3. Remove the transit screw that secures the camera X drag chain bracket to
the camera beam extrusion.
Under Screen
Cleaner
1. Snip the cable ties securing the piece of card to the top of the under screen
cleaner.
2. Remove the cable ties and the piece of card from the printer.
This concludes the transit bracket and screw removal procedure. Transit
brackets, screws and associated fasteners should be stored for future reuse.
Printer Relocation In the event of printer relocation, refer to the Technical Reference Manual,
Transportation chapter for transit bracket and screw fitment procedure.
View on Right Hand Underside of Camera Beam
Transit Screw
Transit Screw
Camera Y Plate
Camera Y Linear Bearing
Camera X Drag Chain Bracket
Camera Beam Extrusion
Lock Nut and
Crinkle Washer
PRINTER PREPARATION
PRINTER HEIGHT AND LEVELLING
Chapter Issue 15, May 20 Installation Manual 4.13
PRINTER HEIGHT AND LEVELLING
Leg Spacers
(Camera Linear
Drive Printer Only)
The mounting feet on the camera linear drive printer must be kept as short as
possible to reduce vibration and oscillation.
To achieve the height required, 8 leg spacers (maximum of two per foot) are
supplied. The leg spacers interlock together and the printer foot locates in the
recess of the top leg spacer.
1. Using the table below, determine the amount of leg spacers to achieve the
required printer height:
NOTE
The amount of exposed thread of the printer leg should be kept to a mini-
mum to ensure printer accuracy remains within limits.
2. Place the correct number of leg spacers under each corner mounting foot.
Do not place leg spacers under the centre rear mounting foot. Lower the
printer ensuring that each foot is located inside the recessed top, figure
below refers.
NOTE
Do not attempt to manoeuvre the printer into position whilst mounted on the
leg spacers. The printer must be lifted, moved and lowered ensuring that
the leg spacers are moved with the printer.
Transport Height Leg Spacers Required
840mm - 895mm 0
896mm - 940mm 1
941mm - 980mm 2
Leg Spacers
(2 shown)
Machine Mounting Foot
M24 Locking Nuts
Machine Frame
Leg Adjusting Nut
PRINTER PREPARATION
PRINTER HEIGHT AND LEVELLING
4.14 Installation Manual Chapter Issue 15, May 20
Type 1, 2, 3 and 5
Printers
Before operation, the printer must be installed at the correct height and levelled.
The height of the printer is governed by the external printers that it is to be
connected to and ranges from 840mm to 980mm. The height is measured from
the floor to the top of the transport belts.
The transport height may be adjusted as low as 830mm by removing the M24
full nut on each of the legs. In the event of the transport height being adjusted
above 839mm at a later date, the M24 full nut must be refitted.
NOTE
To achieve reliable DEK SPC testing and Cp/Cpk results, the printer legs must
be secured correctly to the frame to increase the rigidity of the printer.
Height to Top
of Transport Belts
840mm to 980mm
View on Front of Machine
Transport Belts
Washer
Machine Frame
Full Nut
Half Nut
Leg Adjusting Nut
Leg Bolt
Foot