88192278-01-19 Installation Master - 第122页
PRINTER PREPARATION PRINTER HEIGHT AND LEVELLING 4.20 Installation Manual Chapter Issue 15, May 20 8. Lower the printer onto th e floor plate, ensuring foot (3) a nd foot (4) are positioned correctly on the plate and cle…
PRINTER PREPARATION
PRINTER HEIGHT AND LEVELLING
Chapter Issue 15, May 20 Installation Manual 4.19
2. Move printer A into position and align it with the downline printer using two
rectangular PCBs.
3. Using recommended lifting equipment, carefully raise the printer
approximately 10mm off the floor. Avoid any movement in direction X and Y.
4. Check the location blocks and V-blocks on the floor plate are free to move
in X and Y.
5. Check that all four stopper bolts are fully wound in.
6. Place the floor plate under foot (3) and foot (4) of printer A ensuring the
orientation of the floor plate is correct.
7. Ensure the floor plate is positioned inline with foot (3) and foot (4) and
parallel to the rear of the printer (shown above).
Location Blocks x 2
Stopper Bolts
and locking nuts x4
V-Block x 2
Location Block Fixing Screws x 4
Plan Floor PlateView on Machine
/,1(',5(&7,21
0$&+,1(
%
0$&+,1(
$
PRINTER PREPARATION
PRINTER HEIGHT AND LEVELLING
4.20 Installation Manual Chapter Issue 15, May 20
8. Lower the printer onto the floor plate, ensuring foot (3) and foot (4) are
positioned correctly on the plate and clear of the location and V- blocks.
9. Place foot (6) under the front of the printer in the centre.
10. Check the orientation of foot (6) as shown above.
NOTE
Avoid the seam weld to ensure the printer is properly supported.
11. Raise the front centre levelling foot (6) to make contact with the printer.
12. Raise the front left foot (1) and front right foot (2) so they are not in contact
with the floor and the printer is supported on the centre mounting foot (6).
13. Apply pneumatic power to the printer to set the rails to the correct height for
printer levelling.
14. Place an engineering level on top of the manual tooling plate along the front
row of screws running from left to right.
15. Adjust the rear mounting foot (3) and foot (4) to level the printer in the X
direction.
16. Move the engineering level along the centre row of screws running from front
Seam WeldLevelling Foot (6)
Front below FrameView Machine
Engineering LevelManual Tooling Plate
Isometric View on Manual Tooling Plate
Front
Centre Line
(Y direction)
Centre Line
(X direction)
PRINTER PREPARATION
PRINTER HEIGHT AND LEVELLING
Chapter Issue 15, May 20 Installation Manual 4.21
to back.
17. Change the orientation of the Level and adjust the front centre mounting foot
(6) to level the printer in the Y direction.
18. Repeat Steps 16 to 18 until the printer is level in both directions.
19. Carefully lower the front left mounting foot (1) so that it is in contact with the
floor.
20. Recheck the printer level has not been disturbed.
21. Carefully lower the front right mounting foot (2) so that it is in contact with
the floor.
22. Recheck the printer level has not been disturbed.
23. Lower the front centre mounting foot (6) so it is not in contact with the printer.
24. Remove the front centre mounting foot (6) and store in a safe place.
25. Tighten mounting feet locknuts.
26. Recheck the printer is level.
27. Recheck the printer height has not been disturbed.
28. Remove the engineering level from the printer.
29. Position the V-block so contact is made with the locating collar on foot (3).
30. Position the location block so contact is made with the locating collar on foot
(4).
31. Fully tighten the fixing screws securing both location blocks.
32. Position the locator blocks for printer B to achieve maximum adjustment,
V-Block
Fixing Screws
Location-Block
Fixing Screws