00191457-02 - 第21页
Retrofit instructions Nozzle changer SIPLACE HS-50 / HS-60 / D4 06/2006 Edition 21 2 Fig. 2 - 3 Installing the nozzle changer and ejector device (1) Used tape guide ch annel (2) 2 x parallel pins for centering the ejecto…
Retrofit instructions Nozzle changer SIPLACE HS-50 / HS-60 / D4
06/2006 Edition
20
2.5 Preparatory work
: Dock the component trolley from its location out of the machine.
: Switch the placement machine off at the main switch.
: Move the gantry to gain easy access to the working surface.
2.6 Installing the 1st nozzle changer
Fig. 2 - 1 shows the locations for installing the first and second nozzle changer for each gantry. 2
2
All the electrical connecting cables and compressed air lines for the nozzle changer are already
installed in placement system. The compressed air lines are sealed with a plug. 2
2
: Remove the plug from the blue compressed air line.
: Attach the y-adapter to the blue compressed air line and seal one end of the y-adapter with a
plug.
: Before installation, position the nozzle changer (item 1 to 4 in Fig. 2 - 2) so that the opening for
the electrical and pneumatic connections at the bottom (item A in Fig. 2 - 2) is pointing in the
direction shown in Fig. 2 - 1.
2
Fig. 2 - 2 Aligning the nozzle changer for installation
(1) Nozzle changer, gantry 1
(2) Nozzle changer, gantry 2
(3) Nozzle changer, gantry 3
(4) Nozzle changer, gantry 4
A Position of the opening on the bottom
of the nozzle changer for connecting the
control cable and compressed air hose
T PCB transport direction 2
Retrofit instructions Nozzle changer SIPLACE HS-50 / HS-60 / D4
06/2006 Edition
21
2
Fig. 2 - 3 Installing the nozzle changer and ejector device
(1) Used tape guide channel
(2) 2 x parallel pins for centering the ejector device
(3) Ejector device
(4) Knurled screw for fixing the ejector device
(5) Nozzle changer
(6) 4 x M4 x 16 hexagon socket-head screws for fixing the nozzle changer
(7) Location of the first nozzle changer
(8) Location of the second nozzle changer
(9) Opening for connecting the control cable and compressed air hose
Retrofit instructions Nozzle changer SIPLACE HS-50 / HS-60 / D4
06/2006 Edition
22
: Plug the control cable into the control board and secure with the two screws.
The following table shows which control cables can be connected to each nozzle changer.
2
: Make sure that the contact surface (item 7 and 8 in Fig. 2 - 3) between the nozzle changer and
the used tape guide channel is clean.
: Place the nozzle changer (item 5 in Fig. 2 - 3) on the used tape guide channel (item 1 in Fig.
2 - 3) at the point identified by item 7 in Fig. 2 - 3.
: Start by loosely tightening the four M4 x 16 hexagon socket-head screws (item 6 in Fig. 2 - 3).
: Then fully tighten the four M4 x 16 hexagon socket-head screws in a diagonally opposite se-
quence.
: Attach the blue compressed air hose of the nozzle changer to the y-adapter.
2
2.7 Installing the ejector device
: Position the ejector device (item 4 in Fig. 2 - 3) so that the two holes in the device are aligned
with the two parallel pins (item 2 in Fig. 2 - 3) on the used tape guide channel.
: Insert the ejector device and fix in place with the knurled screw (item 4 in Fig. 2 - 3).
2
2
2
2
2
2
Cable number Nozzle changer location (see Fig. 2 - 1)
00335293-xx
00335807-xx
No.1 Gantry 1
No. 2 Gantry 1
00335294-xx
00335808-xx
No.1 Gantry 2
No. 2 Gantry 2
00335295-xx
00335809-xx
No.1 Gantry 3
No. 2 Gantry 3
00335296-xx
00335810-xx
No.1 Gantry 4
No. 2 Gantry 4
Tab. 2 - 1 Assignment of control cables to nozzle changer locations