Micron Technical Reference V9 Volume 1 - 第38页

SAFETY FEATURES GENERAL 2.14 Technical Reference Manual C hapter Issue 14, Feb 18 Jog Buttons The two button control switches or jo g buttons are positioned such as to maintain maximum safety for the operator whilst solv…

SAFETY FEATURES

GENERAL

Chapter Issue 14, Feb 18 Technical Reference Manual 2.13

E Stop Module Shut

Down

If the E Stop loop is opened by pressing the E Stop or opening the printhead

cover, an emergency stop is initiated via the E Stop module. When actuated the

following areas of the machine are rendered inactive:

•Lid Bolt

• Moving Rail Stepper

• Print Carriage Servo (axis stopped before power is removed)

• Paste Cartridge Tilt Up/Tilt Down Pneumatic Actuator

• Paste Dispense Solenoid and Stepper Motor

• Rail System Front and Rear Belt Motor Drives

• Rising Table Brake (brake engages when power is cut)

• Rising Table Servo

• Squeegee/ProFlow Stepper Motor(s)

• System Lamp

• Underscreen Cleaner Paper Feed Motor

• Underscreen Cleaner Solvent Pump

• Underscreen Cleaner Squeegee Solenoid

• Vacuum Tooling Solenoid

• X Camera Motor (axis stopped before power is removed)

• X Forward, X Rear and Y Chase Alignment Stepper Motors

• Y Camera Motor (axis stopped before power is removed)

NOTE

The pass through lane belt motors on the Dual Lane machine continue running

when the printhead cover is open but stop when the E Stop is pressed.

Recovery When normal working conditions are restored, release the E Stop switch and,

when prompted by a screen message, press the System button.

Opening Covers Opening printhead covers are fitted with a cam interlock switch to protect

personnel from internal moving parts.

Lid Bolt Lid bolts are fitted to all opening printhead covers to prevent them from being

raised during the print cycle.

The lid bolts are withdrawn and the printhead cover may be raised when:

• Open Cover is requested by software

• Pause or stop is selected during a print cycle

• The E Stop is pressed

SAFETY FEATURES

GENERAL

2.14 Technical Reference Manual Chapter Issue 14, Feb 18

Jog Buttons The two button control switches or jog buttons are positioned such as to

maintain maximum safety for the operator whilst solvent priming or paper

feeding with the printhead cover open. This requires both buttons to be

depressed simultaneously for the function to become active. The use of these

buttons is dependent on the function selected on the machine monitor. During

normal operation these buttons control paper feed and solvent prime opera-

tions. When in maintenance mode, the two button control switches control the

movement of the following diagnostics:

• Print Carriage

• Squeegee Assembly

• Camera Axes

• Rail System

• Screen Alignment

• Rising Table

• ProFlow

Only one button is required to drive the selected mechanism, the two buttons

are used to drive the mechanism in opposite directions, ie jog forward or jog

back.

SAFETY FEATURES

PRINTHEAD COVER

Chapter Issue 14, Feb 18 Technical Reference Manual 2.15

PRINTHEAD COVER

Safety Interlocks The safety features designed into the printer are for the protection of all

operators and maintenance personnel. ASM strongly recommend safety

devices are never overridden.

Opening the printhead cover allows access to the following areas:

• Printhead

• Paste Dispenser

• Squeegee/ProFlow

• Stencil/Screen

• Under Screen Cleaner

• Tooling

The printhead cover is accessible to the operator and an interlock safety switch

protects personnel from the mechanisms during normal line operations. Lifting

the cover cuts power to all motors and selected actuators, via the E Stop

module, to all printer modules.

Full details of the device types fitted can be found in the covers chapter of this

manual.

NOTE

The pass through lane belt motors on the dual lane printer continue running

when the printhead cover is open but stop when the E Stop is pressed.

Pneumatically operated lid bolt(s) prevents the cover being raised during the

print cycle. The lid bolt is withdrawn and the cover may be raised:

• When Open Cover is requested by software

• When pause or stop is selected during a print cycle

• When the E Stop is pressed

Recovery When the printhead cover is closed, normal working condition is restored and

the line may be restarted. Pressing the system button enables resumption of

operations, where this is allowed by the control system.