JANETS_INM - 第512页
JaNets Instr ucti on Man ual 13 . Program D ownloa der 13 - 16 13.9.3 T eaching the component pick - up coordinates in a cluster (in production according to a reser vation file) This is a functio n that allows you to do …
JaNets Instruction Manual 13. Program Downloader
13-15
13.9.2 Check after a production file is specified
When you specify a program to be used for PWB production, the following dialog for specifying the
number of PWBs to be produced appears on the screen.
Create the reservation file in which only the specified production file was registered, in the form of
pd_ + specified production file name.
Figure 13.9-2 “Set Planned No. of PWBs” dialog box
As your confirmation after a production program is specified correctly, the title bar is displayed as
shown below:
Figure 13.9-3 Title bar displayed after a production program is specified
* Data on the active production line is displayed on the screen, and you can use the “Download”
command on the “Production” menu or the “Download” tool button of the toolbar.
* The specified production program is loaded, and the production status of the specified
production program is displayed on the “Production Status” screen of the Line Monitor.
Production line name
Specified production program
OK:
Sets the planned number of PWBs to be
produced.
Cancel:
Cancels a specified production program.
JaNets Instruction Manual 13. Program Downloader
13-16
13.9.3 Teaching the component pick-up coordinates in a cluster (in production
according to a reservation file)
This is a function that allows you to download data for teaching in a reservation file to the main unit
of the machine, teach the component pick-up coordinates and then upload the data so that the
taught pick-up coordinates are taken over to a production program in a cluster.
<Notes>
* If there is no data for teaching in a reservation file, this function cannot be used. To use this
function, enable the “Creation of data for teaching” check box on the “Cluster Options” tab when
the Job Optimizer performs optimization to optimize a reservation file (see Section 8.3.22.1
“Creating data for teaching” of Chapter 8 “Job Optimizer” for details).
* To enable this function, select the “Yes” radio button for the menu item “Cluster teaching” on the
“Production” screen invoked from the “Set Environments” screen (see Section 13.14.2.1) of the
Program Downloader. Note that the menu item “Inherit Pick Position” is enabled forcibly when
you select the “Yes” radio button for the menu item “Cluster teaching.”
* If the cluster number of the next production program that is to be downloaded is different from that
of the production program being used for the current production when this function is enabled, the
system does not download any production program automatically.
* If the cluster number of a production program to be downloaded is not the same among machines
on the production line when this function is enabled, the system cannot download the production
program. Disable this function, and then download the production program.
* A machine that does not support the component pick-up coordinates takeover function is not
covered with this function. Note that this function cannot be used if there is no machine
supporting the component pick-up coordinates takeover function on a production line used for
production.
13.9.3.1 Downloading data for teaching
When you select [Production] – [Download data for teaching] from the menu, the system loads
data for teaching, and then downloads it to the machine.
* If the cluster number of a production program to be downloaded is not the same among
machines on the production line, the system cannot download the production program.
JaNets Instruction Manual 13. Program Downloader
13-17
13.9.3.2 Uploading data for teaching
When you select [Production] – [Upload data for teaching], the “Upload data for teaching”
confirmation dialog box appears on the screen.
Figure 13.9-4 “Upload data for teaching” dialog box
When you select the <OK> button to close the dialog box above, the system starts teaching.
After the system finishes uploading data, it operates according to your choice of the menu item
“Ending Mode.”
Table 13.9-1 Ending Mode
Ending Mode
Description
Terminate in the state
that teaching is
completed.
Uploads a production program for teaching from a machine to be specified to upload
data and takes over the component pick-up coordinates. If at least one machine
fails to upload data, the system causes all machines to abort an uploading operation.
Cancel this production
Cancels the downloading state of a production program for teaching without uploading
the production program and taking over the component pick-up coordinates.