JANETS_INM - 第571页

JaNets Instr ucti on Man ual 13 . Program D ownloa der 13 - 75 T able 13.16 - 13 Dispenser production contr ol information (K D - 2077) ID code Label (Title) Des cription Dispenser prod uction con trol inform ation 11 St…

100%1 / 755
JaNets Instruction Manual 13. Program Downloader
13-74
Table 13.16-11 Nozzle information (RX-7 series)
ID code
Label (Title)
Description
Nozzle information
9
NozzleID
Nozzle ID
NozzleNumber
Serial number
NozzleName
Nozzle name
PickNum
Number of picked up components
PlaceNum
Number of placed components
PickErrorNum
Frequency of non-pickup errors
TombPickErrorNum
Frequency of tombstone pick-up errors
RecErrorNum
Frequency of recognition errors
CompoHeightError
Number of abnormal-height components
ScrapRate
Number of forcible scraps
PickRate
Pickup rate
PlaceRate
Placement rate
LossFactor
Loss rate
AdhesionNum
Number of detected adhesion
StockOutNum
Number of detected stockout
Table 13.16-12 Production control information (RX-6 dual transport machine)
ID code
Label (Title)
Description
Production control information
10
ProductNum Number of produced boards
ProductCir Number of produced circuits
PickNum Total number of picked components
PlaceNum Total number of placed components
BadMarkNum Number of detected bad marks
BocMarkNum Number of BOC mark recognition errors
AreaMark Number of area mark recognition errors
NoCompo Number of stops due to “No components”
TimeRun Total production execution time
TimePwbIn PWB carry-in wait time
TimePwbOut PWB carry-out wait time
TimePwb PWB transport wait time
TimeRepair Maintenance time
TimeTrouble Trouble stop time
TimeSomeStop Momentary stop time
TimeNoCompo Stop time due to “No components”
PwbWaitDualTime PWB wait time
LaneId Transport lane (0: front. 1: rear)
JaNets Instruction Manual 13. Program Downloader
13-75
Table 13.16-13 Dispenser production control information (KD-2077)
ID code
Label (Title)
Description
Dispenser production control information
11
StationId
Station ID
ProductNum
Number of produced boards
ProductCir
Number of produced circuits
TimeRun
Total production execution time
TimePwb
PWB transport wait time
TimePwbIn
PWB carry-in wait time
TimePwbOut
PWB carry-out wait time
TimeSomeStop
Momentary stop time
TimeRepair
Maintenance time
TimeTrouble
Trouble stop time
TimeNoAdhesive
Stop time due to a shortage of adhesive
TimeDown
Sum total of production stop times
PlaceNum
Number of placed PWBs after completion of application
BadMarkNum
Number of detected bad marks
BocMarkNum
Number of BOC mark recognition errors
NoAdhesive
Number of stop times due to a shortage of adhesive
Table 13.16-14 Dispenser head information (KD-2077)
ID code
Label (Title)
Description
Dispenser head information
12
StationId Station ID
ProductLinkNum Dispenser production control information link No.
HeadNo Head unit
HeadId Head ID
ShotNum Number of application times
CheckNum Number of execution times
MinLimitError Application diameter lower limit error for each PWB
MaxLimitError Application diameter upper limit error for each PWB
AveMinError Average application diameter lower limit error
AveMaxError Average application diameter upper limit error
DiamMinError Directly measured diameter lower limit error
DiamMaxError Directly measured diameter upper limit error
Imbalance Application unbalance error
JaNets Instruction Manual 13. Program Downloader
13-76
Table 13.16-15 Feeder information (JM-10)
ID code
Label (Title)
Description
Feeder information
13
FeederBankKind
Feeder bank type
HoleNo
Feeder hole number
LaneNo
Lane number
CompoName
Component name
PickedNum
Number of times a component was picked up successfully
PlacedNum
Number of times a component was placed on a board successfully
PickErrorNum
Number of component pick-up errors
NoCompoNum
Number of component run-out errors
DiffCompoNum
Number of odd-shaped component errors
ErrorVacNum
Number of retry-over errors
LaserErrorNum
Number of laser errors
VisionErrorNum
Number of image recognition errors
TombErrorNum
Number of tombstone chip errors
LeadBendErrorNum
Number of bent lead errors
CompoDirectionErrorNum
Number of component direction determination errors
InsertDimensionErrorNum
Number of insertable component judgment out of range errors
CompoInsertErrorNum
Number of component insertion error detection errors
LeadCorrectionErrorNum
Number of correction failures
OtherErrorNum
Number of other errors
Table 13.16-16 Tray/MTS information (JM-10)
ID code
Label (Title)
Description
Tray/MTS information
14
FeederBankKind
Feeder bank type
StepNo
Step number
CompoName
Component name
PickedNum
Number of times a component was picked up successfully
PlacedNum
Number of times a component was placed on a board successfully
PickErrorNum
Number of component pick-up errors
NoCompoNum
Number of component run-out errors
ErrorVacNum
Number of retry-over errors
LaserErrorNum
Number of laser errors
VisionErrorNum
Number of image recognition errors
LeadBendErrorNum
Number of bent lead errors
CompoDirectionErrorNum
Number of component direction determination errors
InsertDimensionErrorNum
Number of insertable component judgment out of range errors
CompoInsertErrorNum
Number of component insertion error detection errors
LeadCorrectionErrorNum
Number of correction failures
OtherErrorNum
Number of other errors