IPC 7711A - 第80页
NOTES IPC-771 1A Number: 3.5.1 Revision: A Date: 10/03 Subject: SOT Removal P a g e2o f2 Copyright Association Connecting Electronics Industries Provided by IHS under license with IPC Not for Resale No reproduction or ne…
EQUIPMENT REQUIRED
Soldering system
Removal tip
Soldering handpiece
OPTIONAL EQUIPMENT
Tweezers
MATERIALS
Flux-cored solder
Flux
Cleaner
PROCEDURE
1. Remove conformal coating (if any) and clean work area of any contamination,
oxides or residues.
2. Install removal tip into soldering handpiece.
3. Start with tip temperature of approximately 315°C and change as necessary.
4. Apply flux to all lead/land areas. (See Figure 1.)
5. Remove old solder from tip and thermal shock tip with damp sponge.
6. Tin bottom edges of tip with solder. (See Figure 2.)
7. Lower tip over component contacting ALL leads with tip. (See Figures3&4.)
8. Confirm solder melt of ALL joints and lift component from PWB. (See Figures 4
& 5.) (Surface tension of the tip should lift the component from the board. If this
does not occur, use of tweezers to lift the component is optional.)
9. Release component from tip by wiping on a heat resistant surface.
10. Re-tin tip with solder.
11. Prepare lands for component replacement.
Figure 1 Apply Flux
Figure 2 Tin Tip
SOLDER
Figure 3 Position Tip
Figure 4 Melt All Joints
Figure 5 Lift Component
7711A
Rework of
Electronic Assemblies
Revision: A
Date: 10/03
SOT Removal
Flux Application Method
Number: 3.5.1
Product Class: R, F, W, C
Skill Level: Intermediate
Level of Conformance: High
Material in this manual, IPC-7711 Rework of Electronic Assemblies, was voluntarily established by Technical Committees of
IPC. This material is advisory only and its use or adaptation is entirely voluntary. IPC disclaims all liability of any kind as to the
use, application, or adaptation of this material. Users are also wholly responsible for protecting themselves against all claims
or liabilities for patent infringement. Equipment referenced is for the convenience of the user and does not imply endorsement
by IPC.
Page1of2
Copyright Association Connecting Electronics Industries
Provided by IHS under license with IPC
Not for Resale
No reproduction or networking permitted without license from IHS
--``,``,-`-`,,`,,`,`,,`---
NOTES
IPC-7711A
Number: 3.5.1
Revision: A
Date: 10/03
Subject: SOT Removal
Page2of2
Copyright Association Connecting Electronics Industries
Provided by IHS under license with IPC
Not for Resale
No reproduction or networking permitted without license from IHS
--``,``,-`-`,,`,,`,`,,`---
EQUIPMENT REQUIRED
Soldering system
Removal tips
Tweezer handpiece
MATERIALS
Flux
Flux-cored solder
Cleaner
PROCEDURE
1. Remove conformal coating (if any) and clean work area of any contamination,
oxides or residues.
2. Install removal tip into tweezer handpiece.
3. Start with tip temperature of approximately 315°C and change as necessary.
4. Apply flux to all lead/land areas. (See Figure 1.)
5. Clean residue from tips with damp sponge. (See Figure 2.)
6. Tin tips.
7. Lower tips over component and squeeze handpiece contacting ALL leads with
tips. (See Figures3&4.)
8. Confirm solder melt of ALL joints and lift component from PWB. (See Figures 4
& 5.)
9. Release component from tips by wiping on a heat resistant surface.
10. Prepare lands for component replacement.
Figure 1 Apply Flux
Figure 2 Clean Tips
Figure 3 Position Tips
Figure 4 Melt All Joints
Figure 5 Lift Component
7711A
Rework of
Electronic Assemblies
Revision: A
Date: 10/03
SOT Removal
Flux Application Method – Tweezer
Number: 3.5.2
Product Class: R, F, W, C
Skill Level: Intermediate
Level of Conformance: High
Material in this manual, IPC-7711 Rework of Electronic Assemblies, was voluntarily established by Technical Committees of
IPC. This material is advisory only and its use or adaptation is entirely voluntary. IPC disclaims all liability of any kind as to the
use, application, or adaptation of this material. Users are also wholly responsible for protecting themselves against all claims
or liabilities for patent infringement. Equipment referenced is for the convenience of the user and does not imply endorsement
by IPC.
Page1of2
Copyright Association Connecting Electronics Industries
Provided by IHS under license with IPC
Not for Resale
No reproduction or networking permitted without license from IHS
--``,``,-`-`,,`,,`,`,,`---