00197042-04_SM_X-Serie-S_Customer_EN - 第127页
4 Electrics and control system 4.10 Replacing the I/O control unit Service Manual SIPLACE X-Serie S 06/2019 127 4.9.1 Setting the DIP Switch on the CINX Switch DIP switch Machine type DIP switch left DIP switch right 1 2…
4 Electrics and control system
4.9 Replacing the CAN interface CINX (from serial no. Hxxxx)
126 Service Manual SIPLACE X-Serie S 06/2019
4.9 Replacing the CAN interface CINX (from serial no. Hxxxx)
Parts, equipment and tools
Fig.152: CAN interface CINX
1. CAN Interface CINX [03108598-xx]
2. DIP switches
Overview
Fig.153: CAN interface in the machine
The CAN interface(1) is located between
location 1 and 2, behind the BoxPC(2).
The CAN interface is fixed with Velcro to the
machine base.
The CAN interface also features four con-
nections for diagnostics.
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation. Observe the instructions in section 1.2 "Preparatory work..." [}16].
► Lift off the keyboard.
► Dismantle the lower cover between locations 1 and 2.
► Lift the BoxPC slightly and swing it forwards.
► Unplug all electrical connections to the CAN interface. Mark their positions, to make clear as-
signment easier later on.
► Take the CAN interface out of the machine.
Installation
► Set the DIP switches. (see below).
► Further installation is performed by following the above instructions in the reverse order.
4 Electrics and control system
4.10 Replacing the I/O control unit
Service Manual SIPLACE X-Serie S 06/2019 127
4.9.1 Setting the DIP Switch on the CINX Switch
DIP switch
Machine type DIP switch left DIP switch right
1 2 1 2
X-Series S ON ON ON ON
SX1/SX2 OFF OFF OFF OFF
Connector
Connector Description
CAN 1 Gantry 1
CAN 2 gantry 2
CAN 3 Gantry 3
CAN 4 Gantry 4
4.10 Replacing the I/O control unit
Parts, equipment and tools
●
I/O Control Unit II [03116049-xx]
Overview
Fig.154: I/O control unit
I/O control unit
The I/O control unit is located between loca-
tion 1 and 2, behind the bottom cover.
See the board description: 4.10.1 "I/O con-
trol unit" [}128]
Removal
► Take a note of the component counter reading at the software user interface.
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Unplug all press-fit connections. You might like to mark their positions to make clear assign-
ment easier later on.
► Pull the I/O control unit out of its mount.
Installation
► Follow the removal instructions in reverse order for installation. Also observe the following
instructions:
– Make sure that the DIP switches are configured correctly (see 4.10.1 "I/O control
unit" [}128]).
– Check if the component counter of the software still matches the value you have written
down. If this is not the case, contact your SIPLACE service team.
4 Electrics and control system
4.10 Replacing the I/O control unit
128 Service Manual SIPLACE X-Serie S 06/2019
4.10.1 I/O control unit
NOTICE
Downwards compatibility
The I/O control unit II [03116049-xx] is downwards compatible with I/O control unit
[03052315-xx].
All connections and designations are identical.
Overview
Fig.155: 03116049-01
Fig.156: Overview of I/O control unit [03052315-xx]
1. Status LEDs
2. X9qb: Power supply
3. X1qb: CAN bus 1
4. X10qb: Connection of other I/O modules
possible
5. Red LED
This signals a RESET.
6. H1: 7 segment display
(flashing = O.K.)
7. DIP switch S1
8. Outputs X3qb to X8qb