00197042-04_SM_X-Serie-S_Customer_EN - 第168页
6 Gantries 6.4 Trailing cable and printed circuit boards 168 Service Manual SIPLACE X-Serie S 06/2019 6.4.2 Replacing the Trailing Cable Interface Parts, equipment and tools ● Trailing cable interface gantry 2 and 4 asse…
6 Gantries
6.4 Trailing cable and printed circuit boards
Service Manual SIPLACE X-Serie S 06/2019 167
Fig.211: Fastening screws
► Remove the screws fastening the up-
per end of the trailing cable.
Fig.212: Cables
► Dismantle the cover(1) on the trailing
cable interface(2).
► Mark the cables coming from the trail-
ing cable on the trailing cable interface,
to make clear assignment easier later
on.
► Unplug the cables coming from the
trailing cable at the trailing cable inter-
face.
► Carefully remove the trailing cable from the machine. You might need to enlist the help of a
second person.
Installation
► Installation is performed by following the above instructions in the reverse order. Also observe
the following instructions:
– Clean the trailing cable contact surface on the machine base with a dry cloth.
– Always handle the new trailing cable with care.
– Make sure that the flat ribbon cable and the pneumatic hoses are not rubbed against any
parts or folded. Look out for sharp edges.
– Prepare the trailing cable. Place the old and new trailing cables next to one another and
match the length of the new trailing cable hose to the old one.
– For production reasons, the new trailing cable is supplied with a holder. This new holder
can be dismantled before installation and the holder already in the machine can be used
again.
If you use the new holder, you will need to dismantle all attached items (boards etc.) from
the old holder and attach them to the new holder.
– If hose ends were damaged during removal, cut these with hose cutters.
– Carefully insert the new trailing cable into the prescribed position. Make sure you do not
fold or twist the trailing cable.
– Check that the power track chain runs parallel to the machine base. Move the gantry back
and forth.
– If it is difficult to push the hoses onto the tubes, moisten these first with white spirits or iso-
propanol.
– Secure all screws with Loctite 241.
6 Gantries
6.4 Trailing cable and printed circuit boards
168 Service Manual SIPLACE X-Serie S 06/2019
6.4.2 Replacing the Trailing Cable Interface
Parts, equipment and tools
●
Trailing cable interface gantry 2 and 4 assembly [03071356-xx] or
●
Trailing cable interface gantry 1 and 3 assembly [03071355-xx]
NOTICE
Machines from Serial Number Hxxxx
The trailing cable interface version used for machines from serial number Hxxxx must be at
least -02.
Overview
Fig.213: Overview of circuit boards
1. Cover on the trailing cable interface
2. Vision hotlink adapter
3. Trailing unit interface
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Remove the screws fastening the cover on the trailing cable interface and remove the cover.
► Unplug the electrical connections to the trailing interface. You may want to mark the positions
of these connections to make clear assignment easier later on.
► Remove the screws fastening the trailing interface and remove the interface from the
machine.
Installation
► Follow the removal instructions in reverse order for installation.
6 Gantries
6.4 Trailing cable and printed circuit boards
Service Manual SIPLACE X-Serie S 06/2019 169
6.4.3 Replacing the Vision Base Interface (VBI)
The Vision Base Interface is fitted in machines from serial number Hxxxx.
Parts, equipment and tools
●
Vision Base Interface (VBI) [03115474‑xx]
Overview
Fig.214: Vision base interface [03115474-xx]
The Vision Base Interface [03115474‑xx] is
fitted next to the trailing cable interface.
J1: Not used
J3: BoxPC
J4: Not used
J6: Power supply
J8: Stationary camera
J11: Trailing cable (head)
J19: Not used
J20: Not used
Removal/installation
► Removal and installation of the Vision Base Interface (VBI) is the same as that for the trailing
cable interface. Please read section 6.4.2 "Replacing the Trailing Cable Interface" [}168].
► Checking the embedded software and performing a download if needed.
6.9 "eSW Download (SW 70x)" [}202]