00197042-04_SM_X-Serie-S_Customer_EN - 第22页
1 Introduction 1.3 Other instructions 22 Service Manual SIPLACE X-Serie S 06/2019 1.3.6 Release History Release Amendments 07/2013 Initial release 01/2014 Amendments, corrections and supplements: ● Supplements for X4i S …
1 Introduction
1.3 Other instructions
Service Manual SIPLACE X-Serie S 06/2019 21
1.3.4.4 Measurements and modifications to ESD modules
Only perform measurements on modules if one of the following conditions is fulfilled:
●
You are using an earthed measuring device (e.g. via PE conductors)
●
You are using a potential-free measuring device and discharge the measuring head before
the measurement (e.g.by touching an unpainted metal part of the controller casing).
► Always use an earthed soldering iron if you carry out any soldering work.
1.3.4.5 Dispatching ESD modules
► Always store modules and components in conductive packaging (e.g. metallized plastic bags
or metal sleeves) and dispatch them in conductive packaging
► If the packaging is not conductive, place the modules in a conductive envelope before pack-
aging. Use conductive expanded rubber, ESD bags, domestic aluminum foil or paper, for
example. NEVER use plastic bags or film.
► If the module has integral batteries, ensure that the conductive packaging does not touch or
short circuit the battery terminals and, if necessary, first cover the terminals with insulating
tape or material.
1.3.5 Validity of Document
This document contains service work instructions for all SIPLACEX3 S, X4and X4iS machines.
The service work described in this manual is divided into modules and is largely identical for all
machine types:
●
If the work required for specific machines differs from the standard procedure, this will be in-
dicated with reference to the machine number, series and delivery state.
●
Diagrams should be seen as examples e.g. the diagram of a SIPLACEX3 S or a different
machine paint finish does not mean that the following information only applies to the machine
type shown.
The manual focuses on describing mechanical service work.
Please refer to the circuit diagram folder for any electrical checks:
●
Detailed circuit diagrams folder for SIPLACE X-Series S (up to Gxxxx) [DE+EN:00197021‑xx]
●
Detailed circuit diagrams folder for SIPLACE X-Series S (from Hxxxx) [DE+EN:00197920‑xx]
1 Introduction
1.3 Other instructions
22 Service Manual SIPLACE X-Serie S 06/2019
1.3.6 Release History
Release Amendments
07/2013 Initial release
01/2014 Amendments, corrections and supplements:
●
Supplements for X4i S micron, X4 S micron
●
Basic machine: checking screwed connections on the gas pressure shock
absorbers, setting the machine covers, guide rollers
●
Electrics and control: voltage pulsed power pack A8, CAN switch
●
Pneumatics: main switch, motor protection switch, motor protection trip
block, sealing screwed connections
●
Gantry: trailing cable, PCB camera, pressure sensor
●
Conveyor: moving conveyor sides, clamping units, idler pulleys, laser light
barrier transmitter/receiver, conveyor widths SC
●
Placement heads: supplements for C&P20 P
●
Nozzle changers: new nozzle changer, switching unit
●
Changeover table: actuator
●
Docking station: FCU
●
SPS: round cable
07/2015 Amendments, corrections and supplements:
●
X module upgrade
●
Basic machine: setting the covers
●
Electrics: absence of voltage, SMPS power supply, motor protection switch,
shunt opening release, indicator lamp
●
Controls: CAN interface, GigE Ethernet adapter, LAN card, I/O control unit,
BoxPC, hotlink interface card
●
Pneumatics: proportional controller
●
Gantry: MGCU, Vision Base Interface, Vision Head Interface, trailing cable,
guide trolley, X and Y motor, head plate sensors, pressure sensor, head in-
terface
●
Conveyor: clamping units
●
Placement heads: C&P20 P, stationary cameras
●
Nozzle changer: nozzle changer, valve n/a, switching unit n/a
●
Measurement tools
●
COT insert: reject bin sensors, FCU
●
Tape cutter: setting times, baffle plate
●
Docking station: power pack
●
Board descriptions: Vision Base Interface, Vision Head Interface, SPS con-
trol board, I/O control unit, head interface, X basic adapter Twin, FCU
1 Introduction
1.3 Other instructions
Service Manual SIPLACE X-Serie S 06/2019 23
Release Amendments
06/2019 Amendments, corrections and supplements:
●
Supplement to the micron machines
●
Safety instructions (updated, socket, new lockout)
●
Cameras (troubleshooting and cleaning)
●
Basic machine:
guide rollers on the covers (new item no.)
nozzle changer (new version)
●
Power supply:
distributors (DIP switch)
Absence of voltage (revised)
Contactor safety breaker (revised)
distributor and fuse board (revised)
●
Electrics and control:
BoxPC and working memory (revised)
cover switch (revised)
indicator lamp (new version supplemented)
pushbutton (new section)
●
Pneumatics:
locking compressed air inlet (revised)
setting pressure for machine components (revised)
pressure regulator (revised)
pneumatics assy (revised)
proportional controller (revised, new version)
●
Gantry:
incremental encoder (new version, testing devices)
Vision Head Interface (troubleshooting)
head interface (GigE)
pressure sensor (revised)
●
Conveyor:
moving the conveyor side walls(revised)
adjusting the conveyor side walls (revised)
lifting table plate (revised)
calibrating the motor (revised)
toothed belt for conveyor (revised)
laser light barrier (new version)
fiber optic cable sensors (revised)
●
Head exchange:
new heads for Micron
Fast Hardware Exchange (revised)
SIPLACE CPP (GigE supplemented)
hose lengths (supplemented)
●
Tape cutter (fully revised)
●
COT insert (new FCU)
●
Component trolley (bearing assy, actuator/protective bracket)
●
SPS (screw locking varnish)
●
Complete revision of document structure, various editorial amendments