00197042-04_SM_X-Serie-S_Customer_EN - 第31页

2 Basic Machine 2.4 Setting the Covers Service Manual SIPLACE X-Serie S 06/2019 31 2.4 Setting the Covers 2.4.1 Overview Fig.16: Overview of Settings 1. Setting the cover switch See 2.4.2 "Setting the Cover Switch&…

2 Basic Machine

2.3 Guide Rollers on the Covers

30 Service Manual SIPLACE X-Serie S 06/2019

Procedure

► To make the work easier, proceed as follows:

Dismantle the bottom stop.

► Loosen the screwed fixture on the roller (fork wrench size10). Unscrew as far as required.

Fig.15: Threaded pin

► From the inside, screw on a threaded pin as lock and tighten it.

Checks

NOTICE

Covering

Between the roller and the guidance there must be at least 75% coverage along the entire

length of the guide rails.

► Check whether the cover can be easily moved along the whole area. Adjust the cover if ne-

cessary (see 2.4 "Setting the Covers" [}31]).

2 Basic Machine

2.4 Setting the Covers

Service Manual SIPLACE X-Serie S 06/2019 31

2.4 Setting the Covers

2.4.1 Overview

Fig.16: Overview of Settings

1. Setting the cover switch

See 2.4.2 "Setting the Cover

Switch" [}31]

2. Setting the cover switch centering

See 2.4.3 "Setting the Cover Switch

Centering Device" [}32]

3. Setting the actuator

See 2.4.4 "Setting the Actuator" [}32]

4. Setting the bottom stop

See 2.4.5 "Setting the Bottom

Stop" [}33]

5. Setting the rollers

See 2.4.6 "Setting the Cover

Rollers" [}34]

2.4.2 Setting the Cover Switch

Fig.17: Cover switch (example of SIPLACE SX2 shown)

Cover switch [03055262-xx]

► Loosen the screws fastening the cover

switch, the centering device and the ac-

tuator, so that the assemblies can be

easily moved.

CAUTION

Screws on actuator

With enforcement of the Machinery Directive DIN EN 1088 (2009), the following has been

executed to avoid misuse (e.g. putting the safety features out of action): the actuator and

machine protective switch screws have been replaced by Torx screws with pins. The relev-

ant set of tools may only be used for performing repair work.

Fig.18: Cover switch (example of SIPLACE SX2 shown)

► Close the cover far enough for the actu-

ator to be just over the switch. Align

them so that the metal bracket is parallel

to the opening in the switch. The metal

bracket may not scrape against the

cover switch.

► Tighten the cover switch screws in this

position.

2 Basic Machine

2.4 Setting the Covers

32 Service Manual SIPLACE X-Serie S 06/2019

2.4.3 Setting the Cover Switch Centering Device

Fig.19: Cover switch (example of SIPLACE SX2 shown)

► Close the cover a little more until the

plastic centering device for the actuator

is against the cover switch centering

device. These two must be centered to-

wards one another.

► Tighten the screws for the cover switch

centering device.

2.4.4 Setting the Actuator

Fig.20: Setting (example of SIPLACE SX2 shown)

Actuating bracket B1-2053 for AZ15/16

[00321649‑xx]

► Close the cover completely.

► Set the actuator so that it stands ap-

prox. 2 mm above the machine center

and tighten the screws.

 CAUTION!

The cover switch is not suitable as a

stop.

The cover switch is not a stop or a

support for the cover. Use the bottom

stops of the rollers for this (see next

section).

Neither the cover nor the actuator may

be supported on the cover switch.

There must be a visible gap between

the actuator and the cover switch.