00197042-04_SM_X-Serie-S_Customer_EN - 第351页
9 Component feeding 9.1 Cutter Service Manual SIPLACE X-Serie S 06/2019 351 9.1.13 Replacing the throttle valve Parts Fig.467: Throttle valve 03000600‑xx Throttle valve AS2201F-02-06SA Equipment and tools 00096290-xx Fo…
9 Component feeding
9.1 Cutter
350 Service Manual SIPLACE X-Serie S 06/2019
9.1.12 Replacing the cutter cable
Parts
03063590-xx Cutter cable X-Series
Equipment and tools
00353832-xx Allen key set
Wire cutters
Cable ties
Overview
Fig.465: Electrical connections
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Switch off the compressed air supply
5.2 "Disabling the compressed air supply" [}134]
Fig.466: Cutter cable
► Disconnect all sensors and plugs and
remove the cable set completely.
Mark the position of old sensors, espe-
cially the sensors responsible for posi-
tioning the short-stroke cylinders.
Installation
► Fit the new cable set and adjust the sensors to the correct position.
► Follow the removal instructions in reverse order for further installation.
●
Attach cables ties if necessary (strain relief).
9 Component feeding
9.1 Cutter
Service Manual SIPLACE X-Serie S 06/2019 351
9.1.13 Replacing the throttle valve
Parts
Fig.467: Throttle valve
03000600‑xx Throttle valve AS2201F-02-06SA
Equipment and tools
00096290-xx Fork wrench set
Wire cutters
Cable ties
Overview
Fig.468: Throttle valves on cutter
1. Throttle valves
The throttle valves are installed at the lower
sides of the short-stroke cylinders.
Removal
► Switch off the machine, disconnect it from the power supply and secure it to prevent
unauthorized reactivation.
1.2 "Preparatory work..." [}16]
► Switch off the compressed air supply
5.2 "Disabling the compressed air supply" [}134]
► Try to perform the exchange on the installed cutter.
If access is too limited, remove the cutter from the machine.
Replacing the Cutter on the COT Insert [03066690-xx]
9 Component feeding
9.1 Cutter
352 Service Manual SIPLACE X-Serie S 06/2019
Fig.469: Removing the throttle valve
► Disconnect the air tube(1) from the
throttle valve(2).
► Turn the throttle valve in the direction
"-" and count the turns. Note the num-
ber.
► Remove the throttle valve by using a
SW17 spanner(3).
Installation
► Fit the new throttle valve. Take care of the silicon sealing.
► Close the throttle valve completely in direction "-" and open it again in direction “+” by counting
the noted turnings.
This will ensure a working pre-adjustment for starting the final setting later on.
► Connect the air tube.
► Follow the removal instructions in reverse order for further installation.
► Set the new throttle valve (see below).
9.1.13.1 Times for Setting the Throttle on the Cutter (From SW707.1)
Fig.470: Measuring times
► Switch over to Check sensors and
functions
.
► Select the
button.
► Select Location.
► Select the
button.
► Select Cut to start test.
You have to select the Cut button at
least two times (one for each side).
Repeat if necessary.
► Check the measured times.
NOTICE!
The permitted measurement ranges
will be provided by the software.
.
Cutter Time
Moving the blade out 175 to 200 ms
Moving the blade in 200 to 250 ms
► If necessary: Change the time by adjusting the throttle valves at the short-stroke cylinders.