YRM20_Mainte_E.pdf - 第36页

2. Preparing for maintenance tasks 1-3 Chapter 1 Maintenance 2. Preparing for maintenance tasks This section describes mainly about the replacement method of the parts which deteriorate their function gradually upon usin…

100%1 / 181
1. Maintaining machine performance
1-2
Chapter 1 Maintenance
1.2 Importance of periodic inspections and cleaning
Periodic inspections and cleaning are extremely important maintenance tasks. Failure to perform inspections
and cleaning will prevent the machine from delivering full performance and may lead to component
mounting problems or equipment breakdowns.
Examples:
• Dirty nozzle may cause the miss-recognition of nozzle itself and raise mounting failure.
• Dirty air path may cause frequent pickup/mounting errors.
• Inadequate inspection of feeder or feeder plate may cause frequent pickup errors.
• Dirty optical system (camera, lighting, etc.) may cause recognition errors.
• Poor greasing of axes may cause abnormal noises.
• Inadequate inspection of valve etc may cause failure in clamping and transferring a board.
As these examples show, failure to make periodic inspections and cleanings may lead to equipment
problems. It is strongly recommended to perform periodic inspections and cleaning to ensure the
machine is used under optimal conditions.
1.3 Importance of appropriate humidity management
The inappropriate humidity management of the machine installed floor, it triggers dew drops and may
damage the control circuit inside of machine.
Perform the following itmes to secure machine endurance.
■
Check the temperature and humidity of your site before turning on machines.
• Actuate the air conditioner, humidifier or dehumidifier to adjust the temperature and humidity
matched to the environmental condition described in "1.1 Essential conditions and working
environment", confirm the temperature and humidity of your site settle and then turn on machines.
■
Use the humidifier adequetly.
• Use the water without much impurity for humidifier.
• The spray type humidifier should be installed at high place enough from machines. Adjust the
amount of mist to prevent the dew drops on machine surface.
• Adjust the humidifier operation as necessary. Especially the using of humidifier in humid period, the
humidity may excess 80%.
TIP
The water without much impurity refers to that is filtered by the dedicated equipment.
The impurity amount of filtered water can be perceived by the electrical conductivity of water (S/cm);
General tap water in Japan : 100 - 400 μS/cm
Filtered tap water : approx. 1 - 2 μS/cm
c
CAUTION
For your humidifier, DO NOT use tap water or well water. Those water include small amount of elements as such Natrium
or Chlorine, may cause a decline of insulation, and it may damage the circuit inside of machine.
2. Preparing for maintenance tasks
1-3
Chapter 1 Maintenance
2. Preparing for maintenance tasks
This section describes mainly about the replacement method of the parts which deteriorate their
function gradually upon using to maintain machine performance (consumable parts). Also, describes
easy replaceable parts for users upon breaking.
2.1 Consumable parts
The parts listed below are provided as the consumable parts for YRM20, and are replaced upon maintenance
operation as necessary.
2.1.1 HM head unit
Consumable parts (HM head)
Delivered with machine body
Nozzle leaf spring mounting screw
Nozzle leaf spring
Leaf spring for strengthening
the nozzle holding force
Gasket for filter
Ejector filter
53101-KMK-00
Name Part name Part No. Remarks
Nozzle leaf spring LEAF SPRING KG7-M7137-A0X Quantity: 20
Leaf spring for strengthening
nozzle holding force
PLATE, SPRING KGS-M714W-03X Quantity: 20
Nozzle leaf spring mounting
screw
SCREW, PAN HEAD 90990-08J016 Quantity: 20
Ejector filter FILTER KLW-M8527-00X Quantity: 20
Gasket for filter GASKET KLW-M715B-00X Quantity: 20
n
NOTE
The parts (Part Nos.) in this manual are at the time of issuing this manual. The Part Nos. may be changed without prior
notice. Make sure to verify the latest Part Nos. before ordering.
2. Preparing for maintenance tasks
1-4
Chapter 1 Maintenance
2.1.2 RM head unit
Consumable parts (RM head)
Delivered with machine body
Nozzle
Air filter
53102-KMX-00
Name Part name Part No. Remark
Air filter FILTER, 20PCS. KMB-M3856-00X Quantity: 20
n
NOTE
The parts (Part Nos.) in this manual are at the time of issuing this manual. The Part Nos. may be changed without prior
notice. Make sure to verify the latest Part Nos. before ordering.