591968 Heller Chinese Manual Rev-C - 第62页
57 Custom Digita l Switch Digital Output: ___________ _____ Digital Switch F eedback:___ ______________ Label:____________ ______ O2 Sensor Settings: Oxygen Sensor T ype: ____________ O2 Sensor type Single Chan…
56
Page 2
Center Board Support Up/Down
Nitrogen Computer Ctrl.
N2 Auto Purge/Standby
CBS Up/Down Feedback
Second Center Board Support Up/Down
Password Protect NitrogenButton
O2 Sensor Settings
Purge Time: ______ min.
Normal Time: ______ min.
Second CBS Up/Down Feedback
Classic CBS Bitmap[1
st
]
Classic CBS Bitmap[2
nd
]
Flux Condensation Service Option
N2 Purge/Standby Sensor Input:___________________
Heat zone Cooling control. PID Period: __________ Seconds
Heat zone cooling in Cooldown mode
Skip startup seq. for heat zone cooling
Custom Message/Alarm1
[Timed] AirGen-
5
[Recipe] Gen-5
[Recipe] Gen-
9
Purge Output:
RecipeOutput:
Edit Interval in
Operating Program
Autoclean Reminder
______________
_______________
Interval: _______ Hr.
Cycle Duration: Min
Cycle Start Check: Min
Flux Heater Delay: Min
Phase-1 : Min
Phase-2 : Min
Custom Message/Alarm2
Custom Alarm/Warning 3
Custom Digital Switch
Flux Filter (Gen4, service ind)
Interval Time:_______Hr
SEC Light Tower Function
Custom Message on Autoclean.job load:____________________________
Idle Mode Energy Saving Feature
Load Standby Recipe ____ Min
Cooldown Mode ______ Min
Auto Lube # 1
Interval: _____Hrs.
Duration:_____ sec
Auto Lube # 2
Interval: _____Hrs.
Duration:_____ sec
Misc. Options
Redundant Overtemp
High Water Temp
Alarm
Low Exhaust Alarm: (sec)
Warning: 15
Alarm: 30
Users will be automatically Logged off
Log off Time: ______hrs _____min
Auto log down tooperator level
Time: ______ hrs _____min
Dual Light Tower
Dual Lane Barcode (XXxxxxxxx-XXX-XXX)
Board Entry Logging/Barcode
Configuration
File Directory: ________________
Machine Name: ________________
Light Tower Setup
Custom Message/Alarm Setting1:
Digital Input: ________________
Digital Output: _____________________
Light Tower: ________________
Display Text: ________________
(Note: Make sure proper hardware is installed)
Active: _________
Type: __________
Delay: ___ sec
Audible (Buzzer)
Custom Message/Alarm Setting2:
Digital Input: ________________
Digital Output: _____________________
Light Tower: ________________
Display Text: ________________
(Note: Make sure proper hardware is installed)
Active: _________
Type: __________
Delay: ____ sec
Audible (Buzzer)
Custom Alarm/Warning 3
Digital Input: ________________
Digital Output: _____________________
Warning: _______ Sec or cm/inch
Warning Display: ________________
Alarm: _______
Alarm Display: ________________
Active: _________
Act On: __________
Audible Warning (Buzzer)
(Note: for distance setup, time is calculated based on conveyor 1 SP)
57
Custom Digital Switch
Digital Output:________________
Digital Switch Feedback:_________________
Label:__________________
O2 Sensor Settings: Oxygen Sensor
Type:____________
O2 Sensor type
Single Channel Monitor
Multi-Channel Monitor
Additional O2 Sensor Settings
Closed Loop with Standby control
PPM Level Normal: _____
PPM Level Standby: _______
Release Autopurge/Standby Digital Outputs
User can acknowledge connection loss
Alarm2 Selection:
Alarm1
Alarm2 High
Alarm2 Low
Alarm1 Level Normal: _____
Alarm1 Level Standby: ______
(Note: for Closed loop with Standby control option select “Auto
Purge / Standby” option also)
SEC Light Tower Function:
Digital Input: ________________________
Active: ____________
Interval Delay Time: _________ Seconds or Minutes or hours
First Lane Entrance Sensor
Second Lane Entrance Sensor
Third Lane Entrance Sensor
Fourth Lane Entrance Sensor
Solid Light Tower
Board Entry Logging/Barcode, configuration
Panel ID Barcode Setting
COM Port: _______
Bits per second: ________
Data bits: ________
Parity: ________
Stop bits: _______
58
Page 3
Blower Control Setup:
RPM Warning Level: _______, _______, ________ Type: ___________________
% or RPM Single or L-M-H Inte. Exh. Standby Mode Low/Min Medium High Labels
Group A:
____
_____ _____ __________
Group B:
____
_____ _____ __________
Group C:
____
_____ _____ __________
Group D:
____
_____ _____ __________
Group E:
____
_____ _____ __________
Blower Initial 100% On Time: __15__ Sec.
Blowers at 100% during recipe startup
Upstream Signal : ___________________________
Select Blower RPM Setup file: _________________________
(Warning for RPM setup, make sure that blower RPM graph(*.csv) file has correct data according to control hardware and blower
used.)
Blower Failure:
Blower RPM Port Setup…
Alarm 30 Sec.
Warning 15 Sec.
Audible Warning
Enable Terminal Read….
Select Analog (Thermocouple) Input:
Select TPO Output:
Visible Flux 1 heater
Flux 1 heater
________________________
____________________
Visible Flux 2 heater
Flux 2 heater
________________________
____________________
Visible Flux 3 heater
Flux 3 heater
________________________
____________________
Top 13:
________________________
____________________
Bottom 13:
________________________
____________________
Top 14:
________________________
____________________
Bottom 14:
________________________
____________________
Blower RPM Port Setting
PC Communication Settings
Blower RPM Port Settings
COM Port:
__________
Number of Boards:
_____
Bits per second:
4800
Sampling rate (Sec):
5
Data bits:
8
Alarm Relay RPM Value:
1000
Parity:
None
Max Blowers:
_____
Stop bits:
1
Terminal Read Setting
Tag Label: ___________
COM Port: ___________
Bits per second: _______
Data Bits: ____________
Parity:_______________
Stop bits: ____________