OM-1833-001w_SL - 第119页

1504-001 10.1 Accessories for SL Feeders (optional) Note Here we indicate the number of multi-reel stockers that can be loaded in one cart. For the SIGMA-G5 and SIGMA-G5S, it is not possible to fully load the cart with m…

100%1 / 122
1504-001
10.1 Accessories for SL Feeders (optional)
(3) Magnetism Checker SL-MC100
In indexing of the tape,for the embossed tape components which will not
stay with stable position in the pockets of the carrer tape, the automatic
decelerating of the tape indexing works in advance, however, this automatic
decelerating can be canceld depending on components. In case of that the
component can be magnetized, the magnet tted under the pickup section
will suppress the rampage of components. This with or without check of
magnetism should not be done for the component alone, but it is necessary to
perform the check by the magnetic suck effect through the carrier tape.
Magnetism Checker
Fig. J3
(4) Multi-Reels Stocker (for SIGMA-G5/F8/G5S)
This stocker allows the foregoing tape and the following resupply tape to be
set simultaneously in the respective lane. And it prevents from moving up of
a reel in reel-end.
Multi-Reel Stocker External
Appearance
Installation Example
SL-MR200
for SIGMA-G5
SL-MR800
for SIGMA-F8/G5S
Fig. J4
OM-1833
10-2
1504-001
10.1 Accessories for SL Feeders (optional)
Note
Here we indicate the number of multi-reel stockers that can be loaded in one
cart.
For the SIGMA-G5 and SIGMA-G5S, it is not possible to fully load the cart
with multi-reel stockers.
Table J1
No.
Applicable
machine
Model
Maximum
loadable
number
Number of
small reels set-
table
Remarks
1 SIGMA-G5 SL-MR200 13 104 104 = 4 Lane × 2 Reel × 13 Stocker
2 SIGMA-F8
SL-MR800
10 80 80 = 4 Lane × 2 Reel × 10 Stocker
3 SIGMA-G5S 13 104 104 = 4 Lane × 2 Reel × 13 Stocker
Note
Example of storing Foregoing and After tape reels (Recommendation)
A total of eight small reels can be set in a width of two feeder slots.
AB
SL Feeder
#1
A
B
SL Feeder
#2
1 stoker
2 feeders
Feeder #1
Lane A
After tape
Feeder #1
Lane A
Foregoing
tape
Feeder #1
Lane B
Foregoing
tape
Feeder #1
Lane B
After tape
Feeder #2
Lane A
After tape
Feeder #2
Lane A
Foregoing
tape
Feeder #2
Lane B
After tape
Feeder #2
Lane B
Foregoing
tape
Empty
Fig. J5
OM-1833
10-3
1504-001
10.2 Applicable machines (units) and software upgrades
10.2 Applicable machines (units) and software upgrades
Machines (units) compatible with SL feeders: SIGMA-G5, SIGMA-F8, SIGMA-
G5S
In order to use SL feeders with the above compatible machines, the machine unit
itself must be modied, and the machine unit's software and the NT software must
be upgraded.
Special specications for modied machine units
In order to use the SL feeders, the unit (F8/G5S: cutter guide) and cart (G5: cutter
guide, F8/G5S: feeder cover) require special design modications.
Table J2
No.
Applicable
machine
Unit
Special-order
number
Remarks
1 SIGMA-G5 Cart GS-S198-01 Improved maintainability
2
SIGMA-F8
Unit retrot GS-S199-05
3 Cart GS-S199-06
4
SIGMA-G5S
Unit retrot GS-S199-01
Units shipped before
April 2014
5
Unit (tray)
retrot
GS-S199-02
Units shipped before
April 2014
6 Cart GS-S199-03
7 Cart (tray) GS-S199-04
OM-1833
10-4