YAMAHA errer code-a - 第14页

Ea - 14 ERROR MESSAGES LIST Ea Ea00665 Ea00666 Ea00667 Ea00668 Ea00669 /B Ea00669 /A Ea00670 /B Ea00670 /A Ea00671 Ea00672 Ea00673 /B Ea00673 /A Ea00674 DA T A ERROR Failed to distribute nozzles. DA T A ERROR Failed to d…

Ea -13

ERROR MESSAGES LIST

Ea00602

Ea00603

Ea00604

Ea00605

Ea00610

Ea00611

Ea00620

Ea00621

Ea00622

Ea00623

Ea00624

Ea00625

Ea00642

Ea00643

DATA ERROR

The number of used nozzle exceeds your possession.

Machine 1

Nozzle_type 2

DATA ERROR

The number of component data exceeds system limit.

Machine 2

DATA ERROR

The number of mount data exceeds system limit.

Machine 2

DATA ERROR

The nozzle is not distributed to head.

Machine SM120

•Some nozzles cannot pick the interfering component.

Check the nozzle type of each components.

•Luck of nozzle number. Check the nozzle number and

head spec. inf..

Failed to access feeder quantity data file.

Failed to access nozzle quantity data file.

DATA ERROR

No component data exists.

Machine 2

PCB CUK93001

Component 150

DATA ERROR

No fiducial data exists for the mount data.

Machine 2

PCB CUK93001

Mount 765

Fiducial 1

DATA ERROR

No mark data exists.

Machine 2

PCB CUK93001

Mark 1

DATA ERROR

No badmark data exists for the mount data.

Machine 2

PCB CUK93001

dispense 765

Badmark 1

DATA ERROR

No fiducial data exists for the dispense data.

Machine 2

PCB CUK93001

dispense 765

Fiducial 1

DATA ERROR

No badmark data exists for the dispense data.

Machine 2

PCB CUK93001

dispense 765

Badmark 1

Dispense machine is not exist.

Failed to open dispense information.

(meaning)The number of nozzles planned for use exceeds the num-

ber available for processing.

(cause)The number of nozzles used to manufacture the data cur-

rently being planned is not enough for the actual processing.

(remedy)If the setting for the number used in processing is wrong,

correct it in the machine configuration. If there are actually too few

nozzles, purchase more, or use the YV112 to create data for the

places where nozzles are to be secured and used.

(meaning)The number of component data exceeds the specifica-

tions.

(cause)Components assigned to the specified machine exceed the

specifications.

(remedy)Shift some of the component data assigned to that ma-

chine to another machine.

(meaning)The number of mounting data exceeds the specifications

for that machine.

(cause)Same as above.

(remedy)Set up the specified components on another machine.

(meaning)In no-nozzle change machine, nozzle is not distributed

to each head.

(cause)Some component is too big size to interfere to nearest

nozzle(head).

(remedy)Check the component size and nozzle type. Check the

number of nozzle and the setting of head spec. inf..

(meaning)An error occurred in accessing the data file containing

the number of feeders to be used.

(cause)There is a problem with the hard disk

(remedy)Try creating the data again from the beginning. If it cannot

be recovered, contact the manufacturer.

(meaning)An error occurred in accessing the data file containing

the number of feeders to be used.

(cause) There is a problem with the hard disk

(remedy)Try creating the data again from the beginning. If it cannot

be recovered, contact the manufacturer.

(meaning)There is no component data.

(cause)Same as above.

(remedy)Create the specified component data.

(meaning)There is no fiducial data.

(cause)Same as above.

(remedy)Create the specified fiducial data.

(meaning)There is no mark data.

(cause)Same as above.

(remedy)Create the mark data.

(meaning)There is no badmark data.

(cause) Same as above.

(remedy)Create the specified badmark data.

(meaning)There is no fiducial data.

(cause)Same as above.

(remedy)Create the specified fiducial data.

(meaning)There is no badmark data.

(cause)Same as above.

(remedy)Create the specified badmark data.

Please select the "Exist" of Dispense Head in MCH_CONFIG.

Fail to make the temporary file.

Ea00645

Ea00647

Ea00648

Ea00649

Ea00650

Ea00651

Ea00653

Ea00658

Ea00660

Ea00661

Ea00662

Ea00663

Ea00664

CAUTION: Now going to convert the data from "Exec" to

"Note" in Mount, Block repeat, Local fiducial and Local

badmark. So, "Exec"data will be deleted. Push the [EN-

TER] key to execute. Push the [ESC] key to cancel this

operation.

"Note" data need to execute the convert from block con-

verted data to original data is not exist.

Machine YV112

CAUTION: Amount of Mount data that executed block

conversion exceeded 2500. Amount of data exceeded

the limit for auto-running. Reduce the number of data.

Amount of 'Mount Data", 'Component Info,' , 'Mark Infor-

mation', 'Block Repeat', 'Fiducial Mark', 'PreDispense' and

'DotDispense' cannot exceed 2560. Push the [ENTER]

key to continue. Push the [ESC] key to cancel this opera-

tion.

There is only one "Exec" data in Block repeat.

PCB DATA ERRORNFORMATION ERROR

No alignment module for the component.

Machine 2

PCB CUK93001

Component 1

PCB DATA ERROR Feeder Information

No dump station for the component. Or the table of the

dumpstation is different from the one of the component.

Machine 2

PCB CUK93001

Component 1

DOT DISPENSE SORT TIMEOUT ERROR

Dispense sort was interrupted by time out error. Dispense

sort was finished, but it is contained the data that stopper

may interfere with other dispense data.

Please check the following:

•Illegal Diameter, Stopper and Pitch data of the nozzle

spec.

COMMAND ERROR

1. [ADJUST ASSISTANT] command is not available for a

component with positive "FixCmpRef."

2. [DRAW THE SHAPE(CMP)] command is not available

for a component with positive "FixCmpRef."

DATA ERROR

Failed to quote component details from its Data Base.

Component 150

specifies an illegal database number.

CheckPoint: DataBase Number

DATA ERROR

Failed to quote mark details from its Data Base.

Mark 150

specifies an illegal database number.

CheckPoint: DataBase Number

DATA ERROR

Failed to set up component or mark information from

Database. MAIN WINDOW should be component info. or

mark info.

Or indicated database may not exist.

Or failed to set up component or mark information into

Database. The indicated record may be protected by pass

word level.

FILE ERROR

Failed to read PCB Data.

DATA ERROR

Failed to set up Fixed feeders at its position.

Component 150

specifies an impossible set position.

The component that feeder position is "Teaching" is ex-

ist.

Change the "FeederPosition" into "Automatic".

Change the "MOUNT DATA CONDITION" into "FEEDER

MOVE".

This is a warning message.

Check the existence of "Note" data in Mount, Block repeat, Local

fiducial, Local badmark.

Calculated mount data over 2500. So check and decrease the

amount of Mount, Block repeat, Local fiducial and Local badmark

within 2560.

This PCB data is not for block. Block data need more than two "Exec"

data in Block repeat.

(meaning)Suitable alignment module for the component is not

equipped on the machine.

(cause)There is an error in the setting in the alignment module for

the component or the component must be mounted by the other

machine.

(remedy)Correct the erroneous setting.

(meaning)Though the component must be dumped to the dump

station, the machine is not equipped with a dump station properly.

(cause)There is an error in the setting in the dump way for the com-

ponent or the machine data. Or the table of the dump station is

different from the table where the component is fixed.

(remedy)Correct the erroneous setting.

(meaning)Dispense sort was interrupted by timeout error.

(cause)Illegal Diameter, Stopper and Pitch data of the nozzle spec.

(remedy)Please check the nozzle spec data.

(meaning)These commands are not available for component with

positive "FixCmpRef.".

(remedy)Use these commands to components data in PCB

[STATIC_COMPONENTS].

(meaning)An error occurred when setting data from the database.

(cause)There is no information in the database corresponding to

the specified database number.

(remedy)Use the database list command to check the existing da-

tabase numbers, and specify an existing number.

(meaning)An error occurred when setting data from the database.

(cause)There is no database corresponding to the specified data-

base.

(remedy)Use the database list command to check the existing da-

tabase numbers, and specify an existing number.

(meaning) Data cannot be set from database.

(cause) An attempt was made to use database setting function on

screen other than component information or mark information

screen.

(remedy) Use [F3] key to switch to component information or mark

information screen.

(meaning)An error occurred in reading the PCB data.

(cause)ÅgPCB data with an asterisk (*) was selected; a machine

which has not been registered was selected; or the PCB data has

been destroyed.

(remedy)In the first two cases, correct the operation. In the last case,

copy the data from the backup disk.

(meaning)An error occurred in attaching the fixed feeder because

of the data created.

(cause)Another fixed feeder already exists in that position, so there

is no space to attach the specified feeder.

(remedy)Find the feeder which is interfering with the fixed feeder,

and remove it, or delete the specification of the fixed feeder which is

causing the problem. If the component that feeder position is

"TEACHING", change to "AUTOMATIC" and execute the optimiza-

tion.

Ea -14

ERROR MESSAGES LIST

Ea00665

Ea00666

Ea00667

Ea00668

Ea00669

Ea00670

Ea00671

Ea00672

Ea00673

Ea00674

DATA ERROR

Failed to distribute nozzles.

DATA ERROR

Failed to distribute mount data.

FILE ERROR

Failed to write PCB Data.

Failed to read Machine Equipment Data.

DATA GENERATOR OBJECT ERROR

Dummy file for DATA GENERATOR doesn't exist.

Possible cause :

1.Object PCB hasn't been selected.

2.Dummy file was deleted because of error.

Counter measures :

1.Select PCB.

2.Select [A1 OBJECT SELECTION] and exit.

DATA GENERATOR OBJECT ERROR

Dummy file for DATA GENERATOR doesn't exist.

Possible cause :

1.Object PCB or line hasn't been selected..

2.Dummy file was deleted because of error.

Counter measures :

1.Select PCB and line.

2.Select [A1 OBJECT SELECTION] and exit.

DATA GENERATOR OBJECT ERROR

This command is not available until you select PCB data.

DATA GENERATOR OBJECT ERROR

This command is not available until you select PCB data

and line.

You have not specified a Machine Number. Please se-

lect, at least, one number.

The dummy file for current object PCB will be deleted.

Will you continue? To abort this process, press [ESC] key.

Nozzle settings are shown below.

A TABLE:[Upper = Head No., Lower = Nozzle Type]

Head 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Nzl. 1 1 1 2 2 2 2 2 2 2 2 3 3 4 4 5

B TABLE:[Upper = Head No., Lower = Nozzle Type]

Head 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Nzl. 1 1 1 2 2 2 2 2 2 2 2 3 3 4 4 5

Nozzle settings are shown below.

Machine 2

A TABLE:[Upper = Head No., Lower = Nozzle Type]

Head 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Nzl. 1 1 1 2 2 2 2 2 2 2 2 3 3 4 4 5

B TABLE:[Upper = Head No., Lower = Nozzle Type]

Head 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Nzl. 1 1 1 2 2 2 2 2 2 2 2 3 3 4 4 5

This PCB is already selected.

(meaning)An error occurred in the nozzle layout when the data was

created.

(cause)If a feeder has already been fixed in that position, the nozzle

could not be positioned in a place where it is possible to pick up

components.

(remedy)Change the position of the fixed feeder.

(meaning)An error occurred in the layout in the mounting data.

(cause)If the data is too complex, an error occurs in the mounting

data and the feeders cannot be positioned.

(remedy)Shift part of the data to another machine.

(meaning)An error occurred in writing the PCB data.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. In any other case, check to see how

often the problem occurs, and contact the manufacturer.

(meaning)An error occurred when reading the model information.

(cause)The software versions do not match, or the model setting

does not match the registered machine data.

(remedy)Register the machine data again and check the versions.

If the versions are different, contact the manufacturer.

(meaning)The dummy file which has to serve as a target for creat-

ing the data does not exist.

(cause)The PCB name has not been selected; the dummy file has

been erroneously deleted; or no line has been selected

(remedy)Select the PCB line.

(meaning)Because PCB data is not selected, the command is not

available.

(cause)Same as above.

(remedy)Select PCB data before executing the command.

(meaning)Because PCB data,line is not selected, the command is

not available.

(cause)Same as above.

(remedy)Select PCB, line before executing the command.

(meaning)The machine number which serves as the target for cre-

ating data has not been selected.

(cause)Same as above.

(remedy)Select the machine.

(meaning)The dummy file of PCB data which currently serves as

the target for creating data will be lost if the command about to be

executed is actually executed.

(cause)Same as above.

(remedy)If losing the dummy file will cause problems, press the

ESC key. If the dummy file can be deleted, press any other key.

(meaning)This shows how the nozzles will be attached as speci-

fied by the PCB data, following creation of the data.

(cause)None

(remedy)None

(meaning)The PCB you are trying to select has already been se-

lected.

(cause)Same as above.

(remedy)None

Ea00675

Ea00676

Ea00677

Ea00678

Ea00679

Ea00680

Ea00681

Ea00682

Ea00683

Ea00684

Ea00690

You cannot select any more PCB.

No type of nozzle can pickup the component.

Component 150

Check Point:

Required Nozzle(Component data)

Nozzle Information

No head to attach the nozzle to in order to pickup the

component.

Component 150

Check Point:

Nozzle Setting (In case of NO_NOZZLE_SUGGESTION)

Feeder Position (In case of fixed feeder)

Un-used Head (In case of 112)

Failed to distribute feeder.

No place to fix the component.

Component 150

Check Point: Fix the position of the component.

Failed to copy PCB data.

NOZZLE SET INFORMATION ERROR

The selected nozzle cannot be fixed to this head.

COMMAND ERROR

[A2 NOZZLE SETTING] is available only in the case that

you select EDITING for NZL.CONDITION SEL.

But you can change to EDITING temporarily. (while you

don't exit from making data mode) If you want to change,

push the [ENTER] key. If you don't want to change, push

any other key.

No head available to handle the component.

Component 150

Check Point:

Component Size

Required Nozzle(Component data)

Wait a moment while

copying PCB data....

Nozzle settings are shown below.

XY TABLE[Upper = Head No., Lower = Nozzle Type]

Head 1 2 3 4 5 6 7 8

Nzl. 1 1 1 2 2 2 2 2

Nozzle settings are shown below.

Machine 2

XY TABLE[Upper = Head No., Lower = Nozzle Type]

Head 1 2 3 4 5 6 7 8

Nzl. 1 1 1 2 2 2 2 2

There is no more than two mount data.

In this condition, this function is not available. You can not

select "REPLACE" or "MULTIPLY COMPONENT" when

Component data is not available.

(meaning)The number of PCBs you are trying to select as fixed

PCBs for data creation exceeds the allowable number

(cause)An attempt was made to register five or more PCBs as fixed

PCBs.

(remedy)Select one of the PCBs already registered as a fixed PCB

and cancel it.

(meaning)An attempt was made to pick up components without an

appropriate nozzle. |

(cause)The setting in the component data for the nozzles to be used

is wrong.

(remedy)Go back to the editing screen and check the component

data.

(meaning)There is no head to which a nozzle which can be used to

pick up the components can be attached.

(cause)If the setting for the recommended nozzle is set to "None",

the nozzles has already been decided by the user, and there is no

empty space; or a fixed feeder is being used, and the appropriate

nozzles cannot be attached to a head which will reach that feeder.

Also, it may be that a head has been installed which cannot move

into the work area, so the nozzle cannot be attached to it.

(remedy)Go back to the editing screen and change the nozzle posi-

tion or the feeder position.

(meaning)An error occurred in the feeder layout when creating the

data.

(cause)Because the data is too complex, ultimately there are no

more places where feeders can be attached. Or there are too many

feeders, so that the layout is logistically impossible

(remedy)Try fixing the setting position for the component where the

problem is occurring, or shift that component to another machine.

(meaning)An error occurred in copying the PCB data.

(cause) There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. In any other case, check to see how

often the problem occurs, and contact the manufacturer.

(meaning)When the nozzle configuration was edited, a setting was

used which attaches a nozzle to a head which can not accommo-

date that nozzle.

(cause)Same as above.

(remedy)Do not attach that nozzle to that head.

(meaning)The nozzle setting is possible only when the nozzle set-

ting conditions are edited manually.

(cause)The nozzle setting was selected even though the nozzle

setting conditions must be edited manually.

(remedy)Do not change that setting, or edit the setting conditions

manually.

(meaning)No head exists which can be used with the components.

(cause)Because the components are too big, there is no head to

which an appropriate nozzle can be attached, or there is something

wrong with the component data setting specifying the nozzle to be

used.

(remedy)Go back to the editing screen and check the component

data.

(meaning)PCB data is being copied. This is not an error message.

(cause)None

(remedy)Please wait until the data has been copied.

(meaning)The bulk substitution and component separation functions

cannot be used because there is no data in the placing information.

(cause)No placing information exists.

(remedy)Input the placing data.

Ea -15

ERROR MESSAGES LIST

Ea00691

Ea00692

Ea00693

Ea00700

Ea00701

Ea00702

Ea00703

Ea00704

Ea00705

Ea00706

Ea00707

Ea00710

There is no more than two componet data.

In this condition, this function is not available. You can not

select "REPLACE" or "MULTIPLY COMPONENT" when

Component data is not available.

There is no more than two mount or component data.

In this condition, this function is not available. You can not

select "RENUMBER COMPONENT" tavailable. when

Component data or Mount data is not available.

Not find new Component number All component number

used

Failed to open component information.

Failed to read component information.

Failed to write component information.

Component information are not selected.

There are components on destination whose name is

same as the one shown below. Would you continue?

Component 3

Component Name R3216

[ESC] key to abort

Other key to continue

The component shown below can not be moved because

it doesn't fulfill the condition.

Component 3

Component Name R3216

The condition for moving component

Not using fixed component reference function

Using feeder optimization

The component shown below uses "Teaching" for "Feeder

Position". Would you continue?

Component 3

Component Name R3216

[ESC] key to abort

Other key to continue

The component is multipled.

Would you define as the alternate component?

[ESC] key is not.

Other key is defined.

Failed to open PCB data.

Machine 2

PCB CUK93001

(meaning)The bulk substitution and component separation func-

tions cannot be used because there is no component data.

(cause)No component information exists.

(remedy)Input the component information.

(meaning)The component number control function cannot be used

because there is no data in the component or placing information.

(cause)There is no component or placing information.

(remedy)Input the component or placing information.

(meaning)Editing is not possible because there is not enough space

available for the remaining component data that has to be regis-

tered.

(cause)There is too much component data registered which is not

needed, or there is too much component data which is actually

being used.

(remedy)If too much unnecessary data has been registered, de-

lete some of it. In any other case, the supplementary editing func-

tion cannot be used.

(meaning)An error occurred in the component in formation file.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. In any other case, check to see how

often the problem occurs, and contact the manufacturer.

(meaning)An error occurred in the component in formation file.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. In any other case, check to see how

often the problem occurs, and contact the manufacturer.

(meaning)An error occurred in the component in formation file.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. In any other case, check to see how

often the problem occurs, and contact the manufacturer.

(meaning)Component information has not been selected.

(cause)Same as above.

(remedy)Select the component information.

(meaning)When components are being moved in the component

information, a component with the same name already exists at

the destination location.

(cause)A component with the same name is already located at that

destination.

(remedy)If having two components with the same name at the des-

tination is not a problem, go ahead with the shift. Otherwise, press

the ESC key to interrupt the shift.

(meaning)In the group of comp. being moved in the component

information screen, a component exists which uses fixed compo-

nent reference function. The component will not be moved.

(cause)Same as above.

(remedy)No remedy.

(meaning)In the group of components being moved on the compo-

nent information screen, feeder position coordinates exist which

are teaching data.

(cause)Same as above.

(remedy)To cancel the movement because of the position coordi-

nate teaching, press the ESC key. To continue the movement press

any other key.

(meaning)When you execute the multiply component, you select

whether using alternate component or not. This component is al-

ready alternated, this function is not used.

(cause)

(remedy)

(meaning)An error occurred when opening the PCB file.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. In any other case, check to see how

often the problem occurs, and contact the manufacturer.

Ea00711

Ea00712

Ea00713

Ea00715

Ea00720

Ea00721

Ea00722

Ea00723

Ea00724

Ea00725

Ea00726

Failed to read PCB data.

Machine 2

PCB CUK93001

Failed to write PCB data.

Machine 2

PCB CUK93001

Failed to copy PCB data.

Machine 2

PCB CUK93001

Failed to fix the component in PCB.

Machine 2PCB CUK93001

Fixed component information error to open fixed compo-

nent information.

Fixed component information error

Failed to read fixed component information.

Fixed component information error

Failed to write fixed component information.

Fixed component information error

Failed to write fixed component information.

Fixed component information error

Specified fixed component doesn’t exist.

Fixed component information error

“Component Name” are different between PCB data and

fixed component.

Fixed component information error

“Feeder Type” are different between PCB data and fixed

component.

You can’t multiply such a component as

•Using fixed component reference function

•Not using feeder optimization

•Tray components

(meaning)An error occurred when opening the PCB file.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. In any other case, check to see how

often the problem occurs, and contact the manufacturer.

(meaning)An error occurred when opening the PCB file.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. In any other case, check to see how

often the problem occurs, and contact the manufacturer.

(meaning)An error occurred when opening the PCB file.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. In any other case, check to see how

often the problem occurs, and contact the manufacturer.

(meaning)Fixed components in the PCB data cannot be fixed.

(cause)The components cannot be fixed because they interfere with

another feeder which has already been fixed.

(remedy)Do not attempt to fix the components causing the interfer-

ence, or stop trying to fix the components which are currently dis-

played.

(meaning)An error occurred when opening the fixed component in-

formation file.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. If there is a problem with the disk,

check to see how often the problem occurs, and contact the manu-

facturer.

(meaning)An error occurred when opening the fixed component in-

formation file.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. If there is a problem with the disk,

check to see how often the problem occurs, and contact the manu-

facturer.

(meaning)An error occurred when opening the fixed component in-

formation file.

(cause)There is no space available on the hard disk, or there is a

problem with the hard disk.

(remedy)If there is no space available, back up any unnecessary

PCB data and then delete it. If there is a problem with the disk,

check to see how often the problem occurs, and contact the manu-

facturer.

(meaning)The specified fixed component information does not ex-

ist.

(cause)There was an error in registering the fixed component refer-

ence number, or the fixed component has not yet been registered.

(remedy)Go back to the editing screen and check the reference

number for the fixed component. If the fixed component has not yet

been registered register it.

(meaning)The component name registered in the PCB data is dif-

ferent from the fixed component being referenced by that compo-

nent.

(cause)Same as above.

(remedy)Change the component name in the PCB data to match

that of the fixed component.

(meaning)The name of the feeder being used in the PCB data is

different from the fixed component feeder being referenced by that

component.

(cause)Same as above.

(remedy)Change the name of the feeder being used in the PCB

data to match that of the fixed component feeder.

(meaning)An attempt was made to input multiple components ref-

erencing fixed components on the component information screen.

(cause)Same as above.

(remedy)There cannot be more than one component referencing

any particular fixed component.