00191185-01 - 第15页

Feeder Fastening Attachment for Component Table (Optiona l) SIPLACE 80 S-20/F4/S-15/F3 Retrofitting Instructions Edition 05/98 Seit e 4 1.5 P recon ditions a nd Restr ictions • So ftware: No prereq uisites in the cas e o…

100%1 / 20
Retrofitting Instructions Feeder Fastening Attachment (Addition) for Component Table SIPLACE 80 S-20/F4/S-15/F3
Edition 05/98
Seite 3
1 Retrofitting Kit for Feeder Fastening Attachment
1.1 General Information
The component table at SIPLACE 80 F with WPC is very heavy. Arrangements must therefore be made that
the customer has an employee at his disposal for the duration of the retrofitting.
1.2 Material Required
Retrofitting kit to fix feeder in place Article No.: 00341238-01
consisting of:
•
Safety claw Article No.: 00337308-01
•
Countersunk screw M4 x 10 Article No.: 00095312-01
• Retrofitting instructions Article No.: 00191185-01
1.3 Tools Required
• Standard tools
• Drilling jig
• Drill
• Bit 3.3 mm
• Tap M4
1.4 Documents
• Valid version of user manual for the placer.
Feeder Fastening Attachment for Component Table (Optional) SIPLACE 80 S-20/F4/S-15/F3 Retrofitting Instructions
Edition 05/98
Seite 4
1.5 Preconditions and Restrictions
• Software: No prerequisites in the case of SIPLACE 80 S-20/F4/S-15/F3.
•
Hardware: Older model SIPLACE 80 S-15/F3 placers with flap opener
•
Feeder modules: Following feeder modules require mechanical work:
24/32 mm S Article No.: 141093-02
44 mm S II Article No.: 141094-02
72 mm S II Article No.: 141097-02
Vibratory stick feeder type II Article No.: 142025-01
Vibratory stick feeder type III Article No.: 142031-03
Vibratory stick feeder Article No.: 142031-04
Basement for bulk case Article No.: 142318-04
If feeder fastening attachments are retrofitted without the required mechanical work
on the following feeders, restrictions on the feeder locations will result.
24/32 mm S track 4/16/28/40/52/64/76/88/100/112
56 mm S track 1/13/25/37/49/61/73/85/97/109
72 mm S track !/19/37/55/73/91
2 Safety Instructions
Retrofitting Instructions Feeder Fastening Attachment (Addition) for Component Table SIPLACE 80 S-20/F4/S-15/F3
Edition 05/98
Seite 5
DANGER
O O O
The machines in the SIPLACE family are powered by 3 x 400 V +/- 10%, 50/60 Hz line voltage.
Portions of the system are therefore conducting dangerous electricity. This voltage is applied to specific
modules inside the machine even while the master switch is turned off!
Unprofessional handling of the machines or contact with portions there of conducting electricity may result in
death, serious injury or considerable material damage.
At all times, observe applicable accident prevention regulations and VDE codes / regulations of the society of
electrical engineers and the special safety regulations in your country. More stringent safety regulations to
VDE 0113 or the corresponding instructions in your country must be adhered to during all work in the
machine.
Only Siemens service engineers
are permitted to carry out these retrofit jobs.
Before starting the retrofitting, turn off the master switch and pull out the mains plug. Secure the machine to
prevent it from being restarted by unauthorized personnel.
2.1 Definitions
DANGER O O O
As used in these instructions, this means that death, serious injury or extensive material damage will occur if
the instructions regarding danger are not observed.
WARNING
O O
As used in these instructions, this means that death, serious injury or extensive material damage may occur if
the instructions in the warnings are not observed.
CAUTION
O
As used in these instructions, this means that minor injury or material damage may occur if the instructions in
the caution message are not observed.
NOTE
As used in these instructions, this means that particular attention is to be directed to important information
regarding the product or the specific part of the instructions.