Productivity Lift - 第85页
User Manual - Productivity Lift Soko 00166631-01 / 12031477 6 Set-up mode Software version V 43.140 Edition April 2006 6.10 PCB inspection 2 77 If the featu re is enab led, the di splay shows „ inspection track 1”. Fig. …
6 Set-up mode User Manual - Productivity Lift Soko 00166631-01 / 12031477
6.9 PCB inspection 1 Software version V 43.140 Edition April 2006
76
6.8.2 PCB hand over
The set up possibilities for the hand over of PCBs at the outlet of the upper transport level. The
following settings are possible:
Track 1 : PCBs are only handed over on track 1 of outlet 1.
Track 2 : PCBs are only handed over on track 2of outlet 1.
Double track : PCBs are handed over on both tracks of outlet 1.
Fig. 6 - 14 PCB hand over
6.9 PCB inspection 1
This feature allows to inspect a PCB on the transport modul placed before the Productivity Lift.
This feature can be enabled for an input or cluster module. The PCB inspection 1 will be con-
ducted on track 1. The entered value defines the control cycle. The value can be set between 0-
99.
Value „0”: Function disabled
Value „1”: Each PCP is stopped
Value „3”: Every third PCB is stopped.
Fig. 6 - 15 PCB inspection 1
ALT
Enter
Start
Stop
PCB hand over
Double track
ALT
Enter
Start
Stop
PCB inspection 1
0 … 99
User Manual - Productivity Lift Soko 00166631-01 / 12031477 6 Set-up mode
Software version V 43.140 Edition April 2006 6.10 PCB inspection 2
77
If the feature is enabled, the display shows „inspection track 1”.
Fig. 6 - 16 Inspection track 1
The PCB transport goes on, if the procedure was quit with the „Enter”- key.
6.10 PCB inspection 2
This feature allows to inspect a PCB on the transport module placed before the Productivity Lift.
This feature can be enabled for an input or cluster module. The PCB inspection 2 will be con-
ducted on track 2. The entered value defines the control cycle. The value can be set between 0-
99.
Value „0”: Function disabled
Value „1”: Each PCP is stopped
Value „3”: Every third PCB is stopped.
Fig. 6 - 17 PCB inspection 2
ALT
Enter
Start
Stop
Unit runs
Inspection track 1
ALT
Enter
Start
Stop
PCB inspection 2
0 … 99
6 Set-up mode User Manual - Productivity Lift Soko 00166631-01 / 12031477
6.11 Address width 1 / Address width 2 Software version V 43.140 Edition April 2006
78
If the feature is enabled, the display shows „inspection track 2”.
Fig. 6 - 18 Inspection track 2
The PCB transport goes on, if the procedure was quit with the „Enter”- key.
6.11 Address width 1 / Address width 2
This function is optional and is concerned with the automatic width adjustment of the productivity
lift. If this option is available, it is inactive if the setting „absolut“ in chapter 5.14 “Width adjustment”
is selected, or the setting „manual“ in chapter 5.12 and 5.13 Width adjustment 1/Width adjustment
2 is selected.
The Siplace pick and place machines dictate the width of the line and certain machine prerequi-
sites must be fulfilled so that the width of the lifts can be automatically adjusted. A machine with
CAN Bus capability must be present in front of the inlet module and after the end module there
must be another pick and place module followed by another machine with CAN-Bus capability.
The machine in front of the inlet module (n-1) has the address 1 and is used to check the transport
width. The machine after the last pick and place machine (n+1) has the address 2 and the data
from this unit and is used for adjustment of the transport width. Since the machine „n+1“ checks
and verifies the width by means of a sensor on the last pick and place machine and conveys this
value via CAN-Bus to the Productivity Lifts, this method ensures that the transport width of the lifts
can only be adjusted when all the pick and place machines have been emptied.
Other settings are possible e.g setting addresses 1 and 2 to the same value. In this case however,
the machine „n-1“ is now responsible for checking and adjusting the transport width and the trans-
port width of the pick and place machines is not taken into consideration.
ALT
Enter
Start
Stop
Unit runs
Inspection track 2