TR7500_Series_Software_ch-v6-3-0.pdf - 第526页
Test Research Inc. 514 TR7500SeriesUserGuide – Software 157; - 158; Unused Ÿ 159; Capital Y, di 熳 esis / umlaut 160; Non-breaking Space 161; Inverted exclamation 162; Cent sign 163; Pound sterling 164; General curre…
Test Research Inc.
TR7500SeriesUserGuide–Software 513
127; - 129;Unused
‚ 130; Low single comma quotation mark
ƒ 131; Function sign
„ 132; Low double comma quotation mark
… 133; Ellipses
† 134; Dagger
‡ 135; Double dagger
ˆ 136; Caret
‰ 137; Per mile sign
Š 138; Capital S Hacek
‹ 139; Less-than sign
Π140; Capital OE ligature
141; - 144;Unused
‘ 145; Single beginning quotation mark
’ 146; Single ending quotation mark
“ 147; Double beginning quotation mark
” 148; Double ending quotation mark
• 149; Dot, middle
– 150; En dash
— 151; Em dash
˜ 152; Tilde
™ 153; Trademark symbol
š 154; Small s Hacek
› 155; Greater-than sign
œ 156; Small oe ligature
Test Research Inc.
514 TR7500SeriesUserGuide–Software
157; - 158;Unused
Ÿ 159;
Capital Y, di 熳 esis / umlaut
160; Non-breaking Space
161; Inverted exclamation
162; Cent sign
163; Pound sterling
164; General currency sign
165; Yen sign
166; Broken vertical bar
167; Section sign
168;
Di 熳 esis / Umlaut
169; Copyright
170; Feminine ordinal
171; Left angle quote, guillemot left
172; Not sign
173; Soft hyphen
174; Registered trademark
175; Macron accent
176; Degree sign
177; Plus or minus
178; Superscript two
179; Superscript three
180; Acute accent
181; Micro sign
182; Paragraph sign
Test Research Inc.
TR7500SeriesUserGuide–Software 515
7.6 不顯示[Communicate Table Wait]訊息
可在登錄檔中新增一 DWORD參數[hidewaitboardinmsg] = 1，使得系統在等待進板時
不顯示[Communicate Table wait]訊息。本功能在桌上型機種上較常使用，以避免[第
二專案(Second Project)]功能開啟時，第二專案測試畫面會跳到主程式的畫面。
7.7 限制代料的數目
可在登錄檔中新增一 DWORD參數[alternativecount] 來控制代料的最大數目。
7.8 發送訊號給Hella-Samlip Magazine
在待測板檢測結果為 Fail的時候，送訊號給 Hella-Samlip Magazine。
版本：TRAOI 3.9 Beta 2009/12/02 以後的版本
1) 功能說明
AOI 主程式檢測出待測板狀態為 FAIL的時候，依序送給韓國 Halle-Samlip Magazine
下面三個訊號
z N.G PCB Out Signal(R702) On (PCÆPLC)
%01#WCSR07021**\r Æ W 表示 Write，1 表示 ON
讀取剛剛寫入的值作確認
%01#RCSR0702**\r Æ R表示 Read，PLC 應該會回傳 %01#RC120，
1 表示 ON
z N.G PCB Information Data Set (DT10000 ~10099) (PCÆPLC)
%01WDD1000010003YYYYMMDDHHMMSS99**\r
Æ W 表示 Write, 10000 / 10003 表示寫入 PLC 暫存器(10000~10003),
Æ YYYYMMDDHHMMSS 表示待測板檢測時間
讀取剛剛寫入的值作確認
%01RDD1000010003**\r Æ R 表示 Read
z N.G PCB Out Finish (R702) Off (PCÆPLC)