SOM-2079-001_w.pdf - 第34页

31 SOM-2079 1005-001 異常 ID 異常名、説明、要因および復帰方法 425201 Output Cnvr PCB Detection PCB's were at inlet and outlet of cnvr. Por favor, veriﬁque posicionamento da PCB no conveyor e continue a operação 425202 Output Cnvr PCB…

SOM-2079

1005-001

異常 ID 異常名、説明、要因および復帰方法

424321 Cnvr Positioning2 Error

An error was detected in transferring the PCB.

Por favor, veriﬁque posicionamento da PCB no conveyor e continue a operação

424322 Cnvr Positioning2 Error

Speed reduction was not performed during transferring operation.

Please return the P.C.B. to the proper position when it is sitting between the

conveyors otherwise, remove the P.C.B. And, the P.C.B. detection sensor might

have had a wrong detection, so please check it to make detections correctly

424323 Cnvr Positioning2 Error

A servo error was found in the movement that the backup base was rising. The

backup jig and pins may be left under the transfer rail.

Cancel the error and perform zeroing operation after that, open the cover to

remove the left backup jig and pins under the transfer rail. Perform the setup

operation again to set the backup jig and the pins to the proper positions.

424324 Cnvr Positioning2 Error

Support pins /Jig were detected before the backup base starts to rise.

Remove the support pins / jig from the backup base. If the removong operation is

difﬁ

cult, perform the function to move the support pin changing position.

424325 Cnvr Positioning2 Error

Error data was transferred in the process of the bad mark transfer.

ease check the conformance between the transfer data and the pattern program

data.

425101 Output Cnvr Overtime

The PCB transport (carry in) from Cnvr Positioning2 did not end in prescribed

time.

Por favor, veriﬁque posicionamento da PCB no conveyor e continue a operação

425102 Output Cnvr Overtime

The PCB transport (exhaust) to output machine did not end in prescribed time.

Por favor, veriﬁque posicionamento da PCB no conveyor e continue a operação

425103 Output Cnvr Overtime

The movement to PCB receiving position did not end in prescribed time.

-----

425104 Output Cnvr Overtime

The movement to the arrangement position did not end in prescribed time.

-----

425105 Output Cnvr Overtime

The PCB transport (carry in) from Cnvr Positioning1 did not end in prescribed

time.

Por favor, veriﬁque posicionamento da PCB no conveyor e continue a operação

425106 Output Cnvr Overtime

The reversal positioning operation did not end in prescribed time.

Por favor, veriﬁque posicionamento da PCB no conveyor e continue a operação

425107 Output Cnvr Overtime

The conveyor upper cover by output side has opened.

Please close the cover. Production can be continued.

6.3 コンベア

SOM-2079

1005-001

異常 ID 異常名、説明、要因および復帰方法

425201 Output Cnvr PCB Detection

PCB's were at inlet and outlet of cnvr.

Por favor, veriﬁque posicionamento da PCB no conveyor e continue a operação

425202 Output Cnvr PCB Detection

There is no PCB on the Cnvr The PCB fell while moving to the receiving position.

Please continue production after checking whether the P.C.B has fallen around a

nveyor. Moreover, please execute the zeroing operation of a pertinent conveyer

from the screen of maintenance/unit adjustment/conveyer when the width of the

conveyer has changed.

425203 Output Cnvr PCB Detection

There is no PCB on the Cnvr The PCB was removed.

-----

425204 Output Cnvr PCB Detection

There is a PCB on the Cnvr The PCB could not be discharged.

Por favor, veriﬁque posicionamento da PCB no conveyor e continue a operação

425205 Output Cnvr PCB Detection

There is no PCB on the conveyer. After the PCB carrying in ended, it can not able

to be detected.

Por favor, veriﬁque posicionamento da PCB no conveyor e continue a operação

425206 Output Cnvr PCB Detection

The PCB was detected by the conveyer entrance sensor.

Por favor, veriﬁque posicionamento da PCB no conveyor e continue a operação

425207 Output Cnvr PCB Detection

The PCB was detected with the conveyer exit sensor.

Please conﬁrm the P.C.B on the conveyer.

425208 Output Cnvr PCB Detection

The exhaust end board sensor of a conveyor exit detected the PCB

Please check the P.C.B on a conveyor.

425209 Output Cnvr PCB Detection

The exhaust end board sensor of a conveyor exit did not detect PCB during

discharge operation.

Please check the sensor.

425210 Output Cnvr PCB Detection

Manual bypass of the PCB was carried out in the state where a PCB is on a

conveyor.

Please remove the P.C.B carried out manual bypass. Production can be

continued.

425211 Output Cnvr PCB Detection

The PCB was not found in the proper position.

Please remove the P.C.B on a conveyor. Production can be continued.

425212 Output Cnvr PCB Detection

Manual bypass of the PCB was carried out.

Please remove the P.C.B carried out manual bypass. Production can be

continued.

6.3 コンベア

SOM-2079

1005-001

異常 ID 異常名、説明、要因および復帰方法

425213 Output Cnvr PCB Detection

PCB on a conveyer was removed in output sync / alternation output process.

Please do reproduction after making the P.C.B return to original state.

425214 Output Cnvr PCB Detection

The state of a PCB on conveyer changed in output sync / alternation output

process.

Please do reproduction after making the P.C.B return to original state.

425215 Output Cnvr PCB Detection

The PCB was detected with the conveyer entrance sensor.

Please return the P.C.B. to the proper position when it is sitting between the

conveyors otherwise, remove the P.C.B. And, the P.C.B. detection sensor might

have had a wrong detection, so please check it to make detections correctly

425216 Output Cnvr PCB Detection

The PCB was detected before carrying-in operation.

Restart the product operation after removing the P.C.B. when it is on the

conveyor.

425217 Output Cnvr PCB Detection

A PCB was detected with the conveyor entrance sensor upon completion of the

output operation.

After checking the P.C.B. on the conveyor, continue the product operation. If no

P.C.B. is there, remove the factor why the sensor was detected upon completion

of the output operation.

425218 Output Cnvr PCB Detection

A PCB was detected with the conveyor exit sensor upon completion of the output

operation.

After checking the P.C.B. on the conveyor, continue the product operation. If no

P.C.B. is there, remove the factor why the sensor was detected upon completion

of the output operation.

425219 Output Cnvr PCB Detection

A PCB was detected with the both sensors of the conveyor entrance and exit

upon completion of the output operation.

After checking the P.C.B. on the conveyor, continue the product operation. If no

P.C.B. is there, remove the factor why the sensor was detected upon completion

of the output operation.

425220 Output Cnvr PCB Detection

The machine let the END PCB remove from the conveyor.

Put the P.C.B. on the output conveyor and perform the "START". The product

operation can be continued that why the machine considers as if the P.C.B. put

was the end P.C.B..

425301 Output Cnvr Error

The carrying in operation was not able to begin.

-----

425302 Output Cnvr Error

The error was detected while carrying in was operating.

Por favor, veriﬁ

que posicionamento da PCB no conveyor e continue a operação

6.3 コンベア