00196044-05 - sg x und x4i fse_en - 第377页

Twin Head Position and assembly the nozzle changer Nozzle changer S tudent Guide (FSE) SIPL ACE X Series and X4I Edition 01/2009 EN T win Head 377 9.5.1.4 Function Description The magazine for standar d nozzles has 1 pos…

100%1 / 632
Twin Head
Nozzle changer Position and assembly the nozzle changer
Student Guide (FSE) SIPLACE X Series and X4I
Twin Head Edition 01/2009 EN
376
9.5 Nozzle changer
9.5.1 Position and assembly the nozzle changer
9.5.1.1 Position
9.5.1.2 Nozzle Changer Position at Location with an MTC
SW 603 allows you to install an MTC in a placement area with 2 gantries. However, you need a special
adapter for the Twin head NC, if using this configuration.
9.5.1.3 Fitting the Nozzle Changer Magazine
9-18: Position of "standard nozzle changer" – sector 3 shown here
Legend
1. Feeder area 1
2. Feeder area 2
3. Feeder area 3
4. Feeder area 4
5. Nozzle changer no. garage 1
6. Standard magazine
7. Magazine for special nozzles or grippers
8. Component reject bin
9-19: Fitting the magazine (X/D3 machine)
The nozzle changer together with the empty tape
duct is fixed on the component docking unit. The
magazines are seated on a common support.
They are centered with two parallel pins and fixed
in place with two countersunk screws.
Legend
1. Fiducial for optical X/Y position recognition of
the magazine carrier.
2. Arrow pointing to changeover table
3. Arrow pointing toward the PCB conveyor
Align the nozzle changer so that the marking hole
(item 1) is on the left, as viewed by the operator (at
the changeover table side).
Twin Head
Position and assembly the nozzle changer Nozzle changer
Student Guide (FSE) SIPLACE X Series and X4I
Edition 01/2009 EN Twin Head
377
9.5.1.4 Function Description
The magazine for standard nozzles has 1 positioning fiducial for position detection, while the magazine
for special nozzles/grippers has two positioning fiducials. The nozzles are fixed by balls in the holder.
They are then either locked for return or released for pickup, depending on the direction of rotation of the
D axis.
Position of the nozzle in the magazines
9-20: Magazine for standard and special nozzles (HF/X/D3 machine shown
here as example)
Legend
1. Standard magazine
2. Positioning fiducia
3. Nozzle garage
4. Magazine for special nozzles
5. Nozzle garage
6. Balls for lifting the nozzles
Legend
1. Double magazine for standard nozzles (pickup
angle SW 505 = 184°)
2. Magazine for special nozzles or grippers
(pickup angle SW 505 = 275°)
3. Index pins for correct positioning of nozzles in
magazine
4. Position of nozzle with the holes for the index
pins.
5. Calibration fiducial for determining the
magazine position
6. Nozzle centering pins
7. The magazines for the special nozzles are
turned by 90° degrees.
Twin Head
Axis Control Nozzle Changer for Twin head
Student Guide (FSE) SIPLACE X Series and X4I
Twin Head Edition 01/2009 EN
378
9.5.2 Nozzle Changer for Twin head
Die SIPLACE HF/HF3 and SIPLACE X machines configured with a Twin head are delivered with a
nozzle changer. This nozzle changer can accommodate up to 12 nozzle magazines. There are two
different magazine types available: standard magazines and magazines for special nozzles or grippers.
The nozzle changer may be installed depend on the configuration at location 1 and/or 3. The nozzle
changer consists of a standard module with 3 nozzle garages, for two nozzles each (standard nozzles)
and one nozzle garage for a special nozzle. This configuration can be extended as shown in the diagram
below.
9.6 Axis Control
9.6.1 Twin Head Axis Dynamics
Due to the wide component spectrum, no generally applicable oscillograms can be displayed for
correct axis function.
The axis dynamics can no longer be influenced by potentiometer settings.
The following function descriptions should help you analyze any malfunctions which occur.
The tables contain a brief description of the correct function and a description of malfunctions, their
possible causes and corresponding solution suggestions.
9-21: Nozzle changer configuration Twin- head
Legend
1. Standard nozzle changer
2. Extended Nozzle changer
3. Complete Nozzle changer
4. Magazine for 1 special nozzle
5. Magazine for 2 standard nozzles
6. Transport direction
NOTE:
The magazines for standard and
special nozzles are freely configurable
with SW 505 or higher.