00196044-05 - sg x und x4i fse_en - 第429页

Component Handling Error Messages on X Feeder X Feeder S tudent Guide (FSE) SIPL ACE X Series and X4I Edition 01/2009 EN Component Handling 429 EEP-WriteErr (Fehler bei der Datensicherung im EEPROM) Red Data backup has n…

100%1 / 632
Component Handling
X Feeder Error Messages on X Feeder
Student Guide (FSE) SIPLACE X Series and X4I
Component Handling Edition 01/2009 EN
428
10.2.8 Error Messages on X Feeder
When the feeder is ready for operation, you will see a green LED. Warnings and error messages are
shown by orange or red LEDs and a text on the LCD display.
Warnings
Error messages
Display LED
display
Meaning Troubleshooting
Remove Foil
(Folie entfernen)
Orange Unable to perform the function
selected with the cover foil
stretched tight (foil rocker is
pushed down).
If the required function is to be
performed, remove the foil from the
toothed wheels and cut it to relax
the foil rocket.
Display LED
display
Meaning Troubleshooting
None Red,
flashing
Application software not
present or faulty → software
remains in boot loader.
Reload the application software.
Handle
(Griff)
Red The feeder module has been
logged in but the removal
handle has not yet been
engaged (pushed in).
Push in the handle until it engages.
Low Voltage
(Unterspannung)
Orange 24V supply voltage has not
reached the switching-on
threshold after being switched
on.
Check the voltage supply.
Low Voltage
(Unterspannung)
Red 24V supply voltage has
exceeded the switching-on
threshold and has then
collapsed.
Check the voltage supply.
Feed Timeout
TransTimeout
(Zeitfehler beim
Gurttransport-
zyklus)
Red Tape transport cycle was not
completed correctly in the set
time (timeout for function
"Feed").
Is the tape reel trapped in the
container?
Is the component trapped in the
pickup area, between the tape and
the component window?
Once you have solved the
blockage, reinitiate the feed-in with
the arrow buttons. The feeder
module will finish the faulty feed run
and will return to its correct position.
Foil Torn
(Folie gerissen)
Red Foil was not tensioned within
the prescribed time.
The foil has probably been torn.
Reinsert the foil and re-tension it.
Foil PeelErr
(Fehler beim
Abziehen der
Folie)
Red Foil has not been correctly
stripped off, although the tape
is being fed in.
The cover foil has probably been
trapped under the pickup window
and therefore not stripped off
properly.
Foil Jam
(Folienstau)
Red Foil motor jammed Toothed wheels blocked by foil?
Component Handling
Error Messages on X Feeder X Feeder
Student Guide (FSE) SIPLACE X Series and X4I
Edition 01/2009 EN Component Handling
429
EEP-WriteErr
(Fehler bei der
Datensicherung
im EEPROM)
Red Data backup has not been
performed correctly in the
EEPROM.
Since the position of the drive is
stored in the EEPROM, a reference
run is necessary in these cases. →
Acknowledge the error with the gray
button. Now confirm request to
perform reference run, with the
yellow button (see Reference Run
for details).
EEP-ReadErr
(Fehler beim
Auslesen des
EEPROMS)
Red Data from the EEPROM have
not been correctly read.
EEP-DataErr
(Fehler beim
Sichern der Daten
im EEPROM)
Red Data backup has not been
performed completely in the
EEPROM.
Reference
Referenz o
Red Tape drive position
information is not available.
Remove the tape. Then perform a
reference run by pressing the yellow
"Foil" button.
CAN BusError
(CAN-Bus-Fehler)
Red CAN Bus Error If pressing reset does not solve the
problem, send the feeder in for
repairs.
ParNotSaved!
Red The parameters were not
saved.
The default parameters are
automatically loaded i.e. the last
operator settings are overwritten →
you may need to change settings
(e.g. cycle). If this error occurs
frequently, replace the control
board.
ParWrongSav
e
Red Parameters were incorrectly
or incompletely saved.
BootFlashErr
FlashDataErr
Red Unable to correctly write data
in boot or application memory.
Replace feeder or control board.
Display LED
display
Meaning Troubleshooting
Component Handling
Pneumatic Tape Cutter Pneumatic Tape Cutter and Empty Tape Duct
Student Guide (FSE) SIPLACE X Series and X4I
Component Handling Edition 01/2009 EN
430
10.3 Pneumatic Tape Cutter
10.3.1 Pneumatic Tape Cutter and Empty Tape Duct
The pneumatic tape cutter unit is fixed to the frame of the docking unit with 4 screws. It separates plastic,
aluminum and paper tapes up to a maximum pocket depth of 25 mm. The tape clippings fall down the
waste slide, into the waste tape bin of the component trolley.
The empty tape duct is constructed so that it covers the cutting edges of the tape cutter (for safety), so
that it controls movement of the empty component tapes to the cutter, so that the component reject bin
is integrated and so that it can receive the various nozzle changers for the C&P6/12/20 and TwinHead.
10-30: Complete docking unit
Legend
1 Frame docking unit 2 Pneumatic Tape Cutter
3 Component reject bin 4 Empty tape duct
5 Support for the nozzle changer