00194598-01.pdf - 第35页

Ceramic substrate centering SIPLACE S- 27 HM 2 Retrofit instructions: ceramic substrate centering for SIPLACE S-27 HM 12/2004 Edition 35 2 Retrofit instructions: ceramic substrate centering fo r SIPLACE S-27 HM S27 HM ce…

100%1 / 66
1 Nachrüstanleitung Keramiksubstrat-Zentrierung SIPLACE S-27 HM Keramiksubstrat-Zentrierung SIPLACE S-27 HM
Ausgabe 12/2004
34
1.12 Fehlermeldungen, mögliche Ursachen
Im Fehlerfall wird folgende Fehlermeldung ausgegeben: 1
– "Fehler Keramiksubstrat-Zentrierung 1" bzw.
– "Fehler Keramiksubstrat-Zentrierung 2"
Der Bestückablauf wird dadurch angehalten. 1
Die Meldung besagt, daß das Berosignal für "geöffnet" (1) / "geschlossen" (0) nicht vorliegt.
Der Zusatz 1 bedeutet: Der Fehler besteht im Bearbeitungsbereich 1 oder 4. 1
– Der Zusatz 2 bedeutet: Der Fehler besteht im Bearbeitungsbereich 2 oder 3.
Mögliche Ursachen:
– Störung im Druckluftzweig / undichter Anschluß / schlechte, fehlende oder falsch zugeordnete
Steckverbindung des Magnetventilkabels am Magnetventil / Defekt des Magnetventils.
– Falscher Ansprechabstand des Näherungsschalters / Zugfeder am Flachzylinder ausgehängt,
schlechte, fehlende oder falsch zugeordnete Steckverbindung des Näherungsschalterkabels
an der X-Zentriereinheit / Defekt des Näherungsschalters.
– Falsch zugeordnete Steckverbindungen auf der Umsetzplatine (X34/X35) oder Steckverbind-
ungen für Transport 1 und 2 vertauscht.
1.13 Instandhaltung
: Reinigen und fetten Sie die Kugelumlaufführung in der X-Zentrierung.
: Prüfen Sie bei Bedarf den pneumatischen Antrieb auf Leichtgängigkeit.
1
1
Ceramic substrate centering SIPLACE S-27 HM 2 Retrofit instructions: ceramic substrate centering for SIPLACE S-27 HM
12/2004 Edition
35
2 Retrofit instructions: ceramic substrate
centering for SIPLACE S-27 HM
S27 HM ceramic substrate centering, single conveyor (item no.: 00118571-xx) 2
S27 HM ceramic substrate centering, dual conveyor(item no.: 00118570-xx) 2
2.1 Overview
– Ceramic substrates can be mechanically and optically centered.
The position of the fiducials on the ceramic substrates can be determined either using the sub-
gantry PCB camera with normal lighting that is installed as standard or with the optional multi-
color PCB camera.
– The mechanical ceramic substrate centering option is used to lock ceramic substrates in the X
and Y directions in a way that doesn't harm the material, but keeps them in a stable position.
– A special design allows ceramic substrates to be populated right up to the edge of the sub-
strate.
– The "mechanical ceramic substrate centering" option is only intended for use where the sta-
tionary conveyor side wall is on the right; the stationary conveyor side wall on the left is a spe-
cial design.
– The "mechanical ceramic substrate centering" option is always installed in both processing ar-
eas of the conveyor; on the dual conveyor, it is normally also installed on both PCB conveyor
tracks.
A ceramic substrate centering retrofit kit only contains the parts needed for one of the place-
ment machine's conveyor tracks.
– The appropriate stop rail and stop unit (set 1, 2 or 3) are fitted to the X axis centering unit to
adapt to the size of substrate to be processed (50 mm to 140 mm). These parts are included
in the retrofit kit in prefitted form (see Section 2.3 and 2.4).
– The lifting table bed must be replaced with one with holes for fixing the option (included with
the option).
– The retrofit may only be carried out by trained engineers.
– When converting to overwide boards (>216 mm wide), the stationary conveyor side wall has
to be moved on the dual conveyor. The ceramic substrate centering unit must be moved in or-
der to do this.
– The ceramic substrate centering option must be removed in order to convert from dual to single
conveyor.
2 Retrofit instructions: ceramic substrate centering for SIPLACE S-27 HM Ceramic substrate centering SIPLACE S-27 HM
12/2004 Edition
36
2
Fig. 2.1 - 1 Arrangement of the ceramic substr. centering units, stationary conveyor side on the right (dual conveyor).
2.1.1 Possible centering modes
The following centering modes for ceramic substrates may be entered under conveyor mode in
the machine data (real.ma).
Location 2
Location 1
Conveyor 2
(left-hand side)
Conveyor 1
(right-hand side)
Gantry 2
Gantry 1
Input
area
Processing
area
Output
area
Mechanical
substrate
centering
Conveyor mode Centering
4 Mechanical substrate centering with normal lighting
5 Multicolor with Y axis clamping only
6 Mechanical ceramic substrate centering with multicolor