00198382-03_UM_SIPLACE-CA4-V2_EN - 第179页
Instruction manual SIPLACE CA4 V2 4 Setting up and commissioning From software version 713.0 Ed ition 12/2019 4.3 Setting up the pl acement machine 179 4 Fig. 4.3 - 10 Adjusting the placement machine in the X and Y direc…
4 Setting up and commissioning Instruction manual SIPLACE CA4 V2
4.3 Setting up the placement machine From software version 713.0 Edition 12/2019
178
4.3.8 Integrating the placement machine into the line
Observe the general warnings in section 4.3.1, page 163.
Observe the warnings for transportation of the placement machine in section 4.3.2, page 164.
For details of tools and equipment, refer to section 4.3.5, page 167.
4.3.8.1 Aligning and adjusting the placement machines in the line
With the fork-lift, raise the placement machine until the weight is taken off the machine feet.
Determine the PCB conveyor height for the placement machine in the line and use the hexa-
gon socket head screw to adjust the height approximately.
You may need to fit the machine feet to the relevant PCB conveyor height (see 4.3.6 on page
168).
Position the placement machine on the free location on the line using the fork-lift.
Pay attention to the alignment of the PCB conveyors and check the distance to the previous
placement machine.
4
4
Align the placement machine in the X and Y direction with the help of the machine spirit level.
Place the machine spirit level in the X and then the Y direction on the sides of the conveyor
in placement area 1 (see fig. 4.3 - 10
). The board conveyor width has been preset:
Single lane conveyor 210 mm
Dual lane conveyor, lane 1 100 mm
Dual lane conveyor, lane 2 210 mm 4
4
Measure the distance between the upper edge of the PCB conveyor belt and the underside.
This distance should be 900 mm, 930 mm or 950 mm.
WARNING
Risk of damage!
If the machine feet on one side hit the ground hard, the fixings may be damaged.
Slowly lower the placement machine.
A second person should look underneath to ensure that all the machine foot touch
the floor at the same time.
PLEASE NOTE
When using the spirit level to adjust the dual lane conveyor in the X direction, always
place it on the outer edges of the placement machine.
Instruction manual SIPLACE CA4 V2 4 Setting up and commissioning
From software version 713.0 Edition 12/2019 4.3 Setting up the placement machine
179
4
Fig. 4.3 - 10 Adjusting the placement machine in the X and Y directions
Use the fork wrench SW36 to adjust the setting screw M24x2x120 (item 1 in fig. 4.3 - 11, page
180
), so that the fluid in the machine spirit level does not deviate from its zero point at the
required conveyor height.
4 Setting up and commissioning Instruction manual SIPLACE CA4 V2
4.3 Setting up the placement machine From software version 713.0 Edition 12/2019
180
4
Fig. 4.3 - 11 Presetting the height of the outer machine feet
(1) Setting screw M24x2x120 for height adjustment
(2) Outer machine foot
(3) Clamping pieces
(4) Hexagon socket-head screw M24x90
Check the required board conveyor height.
Once the placement machine has been aligned, use the torque wrench to tighten the hexagon
socket-head screws M24x90 (item 4) to clamp the clamping pieces at all outer machine feet
(item 3).
4
Use the hook wrench to unscrew the middle machine feet roughly 135 - 145, until these are
positioned firmly on the ground.
Make sure that the middle machine feet are not screwed out too far, thereby unbalancing the
placement machine.
PLEASE NOTE
Vibration at low tightening torques!
The tightening torque is 130 Nm. A lower torque could cause the placement machine to
vibrate.
Use a sufficiently high tightening torque.
(4)
(2)
(1)
(3)