00198382-03_UM_SIPLACE-CA4-V2_EN - 第250页

6 Component handling Instruction manual SIPLACE CA4 V2 6.1 SIPLACE tape feeder modules for SIPLACE CA4 V2 From software version 713.0 Edition 12/2019 250 6 6.1.1.3 Design of the SIPLACE SmartFeeder X The following diagra…

Instruction manual SIPLACE CA4 V2 6 Component handling

From software version 713.0 Edition 12/2019 6.1 SIPLACE tape feeder modules for SIPLACE CA4 V2

249

6 Component handling

6.1 SIPLACE tape feeder modules for SIPLACE CA4 V2

The SIPLACE CA4 V2 uses the SIPLACE SmartFeeder X and the SIPLACE SmartFeeder Xi. The

specified tape feeder modules are compatible with the SIPLACE X-Series S changeover tables.

Key features of the SIPLACE tape feeder modules include high pickup position precision, online

programming and simple handling of feeder module changeovers during the placement process.

The power supply to the feeder modules is contactless and uses an inductive interface. Each

feeder module communicates with the feeder module control unit (FCU) via two optoelectronic

channels (optical fiber). The two interfaces form the EDIF assembly (energy and data interface).

6.1.1 SIPLACE tape feeder module

6.1.1.1 Tape material

The possible tape widths range from 4 mm to 104 mm. The tape material is blister or paper. Com-

ponent tapes with a permanently adhesive cover foil (PSA foil) can also be processed.

The design of the tape feeder modules was based on the following tape standards:

DIN EN 60286-3 (12/1998) / IEC 60286-3 (12/1997)

JIS C 0806-3 (1999)

ANSI/EIA 481-C (10/2003)

IEC 60286-3-2 6

6.1.1.2 Manual removal of tantalum capacitors which were not picked up

To prevent tantalum capacitors which were not picked up from causing the tape material to burn

when it is cut, the user interface has been extended to include the option "Stop immediately on

pickup error". This option must be enabled in SIPLACE Pro. On the placement machine, the com-

ponent that was not picked up is paced forward again until it is ready for removal from the com-

ponent tape. The track is deactivated and the operator is sent an error message to remind him to

pick up the tantalum component from the tape. If an alternative track is available, the placement

machine continues placing. The operator is able to stop the placement machine, however, and re-

move the tantalum component. If no alternative track is available and it is not possible to continue

placement with other components, the placement machine will stop. At this point, the operator can

again remove the tantalum component and acknowledge the error. Once the operator has re-

started the placement machine, placement is continued and components are picked up from the

track that is now enabled once more.

6 Component handling Instruction manual SIPLACE CA4 V2

6.1 SIPLACE tape feeder modules for SIPLACE CA4 V2 From software version 713.0 Edition 12/2019

250

6.1.1.3 Design of the SIPLACE SmartFeeder X

The following diagram shows the design of the SIPLACE SmartFeeder X.

Fig. 6.1 - 1 SIPLACE SmartFeeder X

(1) Entry to the tape guide channel with tape spring

(2) Flap on cover foil container

(3) Removal handle, engaged

(4) Status display

(5) Operating panel - LED display

(6) Foil rocker

(7) Tape guide channel outlet

(8) Front slider guide

(9) Back slider guide

PLEASE NOTE

This software function is also a good idea for expensive components.

 Please observe the safety instructions for capacitors on metallic powder basis (see

section 2.5.4

, page 65).

(1)

(2)

(3)

(4)

(5)

(6)

(8)

(9)

(7)

Instruction manual SIPLACE CA4 V2 6 Component handling

From software version 713.0 Edition 12/2019 6.1 SIPLACE tape feeder modules for SIPLACE CA4 V2

251

6.1.1.4 Design of the SIPLACE SmartFeeder Xi

The following diagram shows the design of the SIPLACE SmartFeeder Xi, using the example of

the SIPLACE SmartFeeder 2 x 8 mm Xi. The SIPLACE SmartFeeder Xi can be recognized by its

slanted and grooved surface on the removal handle.

Fig. 6.1 - 2 SIPLACE SmartFeeder 2 x 8 mm Xi

(1) Entry to the tape guide channel with tape spring

(2) Flap on cover foil container

(3) Removal handle, docked (grooved surface)