00196056-0102 RI Shutterless 3x8 SL - 第28页

Introduction Tools and Equipment 28 Nachrüstanleitung / Retrofit In structions Feeder Module 3x8 mm S 0201/0402 to 5.2 T ools and Equipment Tools You will need various screws to fasten the side plates and the tape duct. …

Introduction

Scope of Delivery

Nachrüstanleitung / Retrofit Instructions Feeder Module 3x8 mm S 0201/0402 to Shutterless (3X8 mm SL)

5Introduction

By exchanging a conventional empty tape duct for a shutterless tape duct you can convert your 3x8 mm

S feeder into a 3x8 mm shutterless feeder in a few easy steps.

This following description outlines the individual steps for this conversion.

5.1 Scope of Delivery

The retrofitting kit for the shutterless feeder can be ordered with the following designation:

Retrofit kit tape feeder 3x8mm SL, Item No. 03053307-01

The retrofit kit contains:

 1 completely assembled tape duct SL feeder

 1 label marked 00141088-01, Item No. 00329723-01

NOTE:

Please note that the conversion should only be performed by specialist personnel who have

been trained to handle 3x8 mm S feeders.

Introduction

Tools and Equipment

28 Nachrüstanleitung / Retrofit Instructions Feeder Module 3x8 mm S 0201/0402 to

5.2 Tools and Equipment

Tools

You will need various screws to fasten the side plates and the tape duct. These will differ, depending on

the function state of the 3x8 mm feeder. For conversion of the feeder, you will also need some of the

following tools:

Other Equipment

After the conversion, the information which converts the feeder into a shutterless feeder or back into an

S feeder needs to be saved in the EEPROM of the feeder. The feeder is assigned a new feeder ID. To

do this, you need to connect the feeder to a PC, on which the software for reprogramming the EEPROM

is installed: Set-SL-ID.

To reprogram the EEPROM, you require the following:

 1 PC with at least one free COM port

 1 CD SW shutterless feeder, Item No. 00387197-01. This CD contains:

– The software Set-SL-ID for programming the feeder EEPROM

– The retrofit guide "Conversion to Shutterless Feeder" (documentation)

 1 interface unit for S feeders, Item No. 00371397-01 (1)

(order option)

 1 power supply unit for SIPLACE feeders, Item No. 03041682-01 (2)

(order option)

Tools Size

Allen keys 1.3 / 1.5 / 0.7 / 2

Flat-bladed screwdriver 3 / 1

Phillips screwdriver 1

Torx screwdriver 0.8 / 0.6

Pozidriv screwdriver 1

Feeler gauge 0.25

NOTE:

The interface unit and the software Set-SL-ID, including this retrofit guide, can be ordered as

one set, specified as Equipment NRS Shutterless Feeder, Item No 00387190-01.

Introduction

Spare Parts

Nachrüstanleitung / Retrofit Instructions Feeder Module 3x8 mm S 0201/0402 to Shutterless (3X8 mm SL)

5.3 Spare Parts

The following spare parts can be ordered for the shutterless tape duct:

 Pickup window 3x8mm S – SL, Item No. 03054425-01

 Tape support 3x8mm SL (spacer), Item No. 03014273-01

5.4 Safety Instructions

5.5 Display Features

Convention for the Use of Hazard Symbols

CAUTION:

The safety instructions in the documentation of the feeder which is to be converted to a

shutterless feeder take precedence.

Always observe the applicable accident prevention regulations and the special safety

regulations in your country for handling laboratory equipment or assemblies outside the

machine.

Indicates actions to be performed by the user

Bold lettering Indicates entries on the graphical user interface of the software Set-SL-ID

NOTE:

Is, for the purposes of this manual, key information about the product or part of the conversion

guide, which needs to be highlighted.

CAUTION:

Is, for the purposes of this conversion manual, a note indicating that minor injuries or damage

to property can occur, if the cautionary measures concerned are not observed.