00193786-02 - 第118页

S I P L A C E G EM S W V e r s i on G EM 505 . 03 SP 1 H O S T I n t e r f a c e M anua l P age 118 o f 241 ©S i e m en s A G, a ll r i gh t s r e s e r v ed 4 . 7 . 11 S 5 F 73 - A l a rm R e po r t B l o ck A ck no wl …

SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual

4.7.9 S5F71 - Alarm Report Block Send

{XE "S5F71"}S5F71 [W] * H<-E

<L [2]

<U1 0> * ALPY Alarm Priority

<L [1]

<L [4]

<U4 {XE "ALID"}ALID> * ALID - Alarm ID

<BOOLEAN {XE "ASTAT"}ASTAT> * T = Alarm On

F = Alarm Off

<U4 {XE "ASER"}ASER> * ASER Alarm Serial Number

<A [16] 'YYYYMMDDhhmmsscc'> * CLOCK

> .

Note: This message is provided only for compatibility with Host computers which support

an older version of GEM.

If the Equipment Constant "{XE "ConfigAlarms"}ConfigAlarms" is set to "1", the

Equipment sends S5F71 instead of the normal S5F1 Alarm Notification Send.

The SIPLACE reports that an alarm condition has changed.

ALID identifies the Alarm.

ASTAT value is "True" (Non-zero) if this alarm is currently On (Unsafe), or "False" (Zero)

if it is currently Off (Safe).

ASER (Alarm Serial Number) is assigned by the Equipment. Its value begins at "1" and

is incremented by 1 for each alarm reported.

ALPY (Alarm Priority) is always zero.

CLOCK indicates the date and time of the alarm change.

Equipment Constant "{XE "WBitS5"}Wbits5" controls whether the Equipment sends

S5F71 with w-bit = "1" (Reply Expected) or "0" (No Reply Expected).

4.7.10 S5F72 - Alarm Report Block Acknowledge

{XE "S5F72"}S5F72 * H->E

<L> .

The Host acknowledges Alarm Report. This Equipment ignores the data portion of

S5F72.

SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual

4.7.11 S5F73 - Alarm Report Block Acknowledge

{XE "S5F73"}S5F73 [W] * H<-E

<L [3]

<U4 {XE "ALID"}ALID> * ALID - Alarm ID

<BOOLEAN {XE "ASTAT"}ASTAT> * T = Alarm On,

F = Alarm Off.

<A [16] 'YYYYMMDDhhmmsscc'> * TIMESTAMP

> .

Note: This message is provided only for compatibility with older Host computers which

support GEM 3.1.

In order for this message to be used, the Equipment Constant "{XE

"ConfigAlarms"}ConfigAlarms" must be set to "2".

The SIPLACE reports that an alarm condition has changed.

ALID identifies the Alarm.

ASTAT value is "True" (Non-zero) if this alarm is currently On (Unsafe), or "False" (Zero)

if it is currently Off (Safe).

{XE "TIMESTAMP"}TIMESTAMP indicates the date and time of the alarm change.

Equipment Constant "{XE "WBitS5"}WBitS5" controls whether the Equipment sends

S5F73 with W-Bit "1" (Reply Expected) or "0" (No Reply Expected).

4.7.12 S5F74 - Alarm Notification Acknowledge

{XE "S5F74"}S5F74 * H->E

<B [1] {XE "ACK5"}ACK5> .

The Host acknowledges Alarm Report. This Equipment ignores ACKC5.

SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual

4.8 Stream 6

4.8.1 S6F1 - Trace Data Send

{XE "S6F1"}S6F1 [W] * H<-E

<L [4]

<U4 {XE "TRID"}TRID> * Trace ID

<U4 {XE "SMPLN"}SMPLN> * Sample Number

<A 'yyyymmddhhmmss'> * STIME - Sample Date and Time

<V> * Variable Value

...

> .

The Equipment sends time driven trace data, as previously requested by the Host using

S2F23.

TRID is the Trace ID as initiated by the Host.

SMPLN is the sample number. The first sample is "1", the next "2", and so on. If {XE

"REPGSZ"}REPGSZ is greater than 1, SMPLN is the number of the last sample

contained in this S6F1.

STIME is the date and time at which this sample was taken. If REPGSZ is greater than

1, STIME is the date and time of the last sample contained in this S6F1.

The V's appear in the same order they were specified in S2F23.

S6F1 is normally single block. However, if the Host erroneously initiates a multiblock

trace using an incorrect S2F23, S6F1 may be multi-block. The Equipment never sends

an Inquire/Grant message preceding S6F1.

Equipment Constant "{XE "WBitS6"}WBitS6" controls whether the Equipment sends

S6F1 with W-Bit "1" (Reply Expected) or "0" (No Reply Expected).

4.8.2 S6F2 - Trace Data Acknowledge

{XE "S6F2"}S6F2 * H->E

<B [1] 00> . * ACKC6

The Host acknowledges the data. The Equipment ignores {XE "ACKC6"}ACKC6.

4.8.3 S6F3 - Annotated Event Report

{XE "S6F3"}S6F3 [W] * H<-E, Multiblock

<L [3]

<U4 {XE "DATAID"}DATAID> * DATAID

<U4 {XE "CEID"}CEID> * Collection Event ID

<L [2]

<U4 {XE "DSID"}DSID> * DSID=RPTID Report ID