00193786-02 - 第73页
S I P L A C E G EM S W V e r s i on G EM 505 . 03 SP 1 H O S T I n t e r f a c e M anua l ©S i e m en s A G, a ll r i gh t s r e s e r v ed page 73 o f 241 0 = P e r m i ss i on g r an t ed 1 = B u s y , t ry aga i n 2 =…
SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual
Page 72 of 241 ©Siemens AG, all rights reserved
58 44mm type III
59 56mm type III
60 S_G_12_S
61 S_G_16_S
62 S_G_24_S
63 S_G_32_S
64 S_G_44_S
65 S_G_56_S
66 72mm-S tape
79 3x8 mm tape
80 8mm Surftape feeder
81 12mm Surftape feeder
82 24mm Surftape feeder
149 8mm tape „long“ 8mm
150 8mm "Schulz" tape
151 Fimecore
152 Nitto
153 Bulk-Case feeder
used in: PICKUPINFOx
FiducialName - Identifier of a fiduvial
Format: U2
used in: FIDUCIALDATA
Filling_level - Number of components in a division of a matrix tray changer
Format: I4
used in: MTCInfo
FillingLevel - unused always 0
Format U4
used in: TAPE_INFO
ForceIndex - programmed placement force
see chapter 3.5 in the SIPLACE Data Interface for a detailed description.
Format: U1
used in: PLACEINFOx
GANTRYGROUPID – ID of the gantry-group
Format: U2
1 = First gantrygroup in direction of transport
2 = Second gantrygroup in direction of transport
GANTRYID – ID of the gantry
Format: U2
1...4 (see charpter 'Machine Areas')
GRANT6 - Permission to send
Format: B[1]
SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual
©Siemens AG, all rights reserved page 73 of 241
0 = Permission granted
1 = Busy, try again
2 = Not interested
>2 = Other errors
3 - 63 reserved
used in: S6F6
HCACK - Host Command Parameter Acknowledge Code
Format: B[1]
0 = Accept, Command has been performed
1 = Command does not exist
2 = Cannot perform now
3 = At least one parameter is invalid
4 = Acknowledge, command will be performed with completion signaled later by an
event
5 = Rejected. Already in desired condition
6 = control state is not remote
7 = recipe not in library
8 = control mode is not „GEM-Host“
9 = bad PP-Body
10 - 63 reserved
used in: S2F42
HEADID – ID of the head within a gantry
Format: U2
In this version there is only 1 head per gantry. HEADID is always = 1.
HEIGHTHEAD - distance between the head and the transport conveyor
During the reference run, the SIPLACE machines measures the difference between the
upper edge of the transport conveyor and the nozzle on segment 1. The HEIGHTHEAD
is then calculated by subtracting the length of the nozzle on segment 1 form the
measured value. The nozzle length is defined in the machine data. So HEIGHTHEAD is
a relative, not an absolute value.
Format:I4
Units are 1/1000 mm
used in : HEIGHTHEADx
JobName Name of the actual job
Format:A
used in: TRACE_PCB_DATA
LeadCount - Number of lead found during package form measurement
Format: U2
used in: PLACEINFOx
SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual
Page 74 of 241 ©Siemens AG, all rights reserved
Length - Length of a package form
Length is returned from the vision system. It’s the „optical“ length of the package form.
Units are 1/1000 mm
Format: U4
used in: PLACEINFOx
Level - Level in the matrix tray changer
Level 1 is the lowest level in matrix tray changer, level 40 the top most. A value of 0
indicates the manual tray.
Format: I2
used in: PICKUPINFOx
LIMITACK - Acknowledgment code for variable limit attribute set
Format: B[1]
1 = LIMITID does not exist
2 = UPPERDB < LIMITMAX
3 = LOWERDB >LIMITMIN
4 = UPPERDB < LOWERDB
5 = Illegal format specified for UPPERDB or LOWERDB
6 = ASCII value cannot be translated to numeric
7 = Duplicate limit definition for this variable
>7 = Other errors
8 - 63 reserved
used in: S2F46
LIMITID - Limit ID
Format: B[1]
used in: S2F45, S2F46, S2F48
LIMITMAX - maximum limit
Format:
used in: S2F48
LIMITMIN - minimum limit
Format:
used in: S2F48
LOCATION - Group of feeders 1..4
For a detailed description see „1.6 Machine Areas"
Used in LOCATION, PICKUPINFOx, PICKUPERRORSLOCx, TRACKFULL,
TRACKEMPTY
LOWERDB - lower boundary of the deadband for a limit
Format
used in: S2F45, S2F48