00193786-02 - 第74页

S I P L A C E G EM S W V e r s i on G EM 505 . 03 SP 1 H O S T I n t e r f a c e M anua l P age 74 o f 241 ©S i e m en s A G, a ll r i gh t s r e s e r v ed L e ng t h - Leng t h o f a pa ck age f o r m Leng t h i s r e …

SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual

0 = Permission granted

1 = Busy, try again

2 = Not interested

>2 = Other errors

3 - 63 reserved

used in: S6F6

HCACK - Host Command Parameter Acknowledge Code

Format: B[1]

0 = Accept, Command has been performed

1 = Command does not exist

2 = Cannot perform now

3 = At least one parameter is invalid

4 = Acknowledge, command will be performed with completion signaled later by an

event

5 = Rejected. Already in desired condition

6 = control state is not remote

7 = recipe not in library

8 = control mode is not „GEM-Host“

9 = bad PP-Body

10 - 63 reserved

used in: S2F42

HEADID – ID of the head within a gantry

Format: U2

In this version there is only 1 head per gantry. HEADID is always = 1.

HEIGHTHEAD - distance between the head and the transport conveyor

During the reference run, the SIPLACE machines measures the difference between the

upper edge of the transport conveyor and the nozzle on segment 1. The HEIGHTHEAD

is then calculated by subtracting the length of the nozzle on segment 1 form the

measured value. The nozzle length is defined in the machine data. So HEIGHTHEAD is

a relative, not an absolute value.

Format:I4

Units are 1/1000 mm

used in : HEIGHTHEADx

JobName Name of the actual job

Format:A

used in: TRACE_PCB_DATA

LeadCount - Number of lead found during package form measurement

Format: U2

used in: PLACEINFOx

SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual

Length - Length of a package form

Length is returned from the vision system. It’s the „optical“ length of the package form.

Units are 1/1000 mm

Format: U4

used in: PLACEINFOx

Level - Level in the matrix tray changer

Level 1 is the lowest level in matrix tray changer, level 40 the top most. A value of 0

indicates the manual tray.

Format: I2

used in: PICKUPINFOx

LIMITACK - Acknowledgment code for variable limit attribute set

Format: B[1]

1 = LIMITID does not exist

2 = UPPERDB < LIMITMAX

3 = LOWERDB >LIMITMIN

4 = UPPERDB < LOWERDB

5 = Illegal format specified for UPPERDB or LOWERDB

6 = ASCII value cannot be translated to numeric

7 = Duplicate limit definition for this variable

>7 = Other errors

8 - 63 reserved

used in: S2F46

LIMITID - Limit ID

Format: B[1]

used in: S2F45, S2F46, S2F48

LIMITMAX - maximum limit

Format:

used in: S2F48

LIMITMIN - minimum limit

Format:

used in: S2F48

LOCATION - Group of feeders 1..4

For a detailed description see „1.6 Machine Areas"

Used in LOCATION, PICKUPINFOx, PICKUPERRORSLOCx, TRACKFULL,

TRACKEMPTY

LOWERDB - lower boundary of the deadband for a limit

Format

used in: S2F45, S2F48

SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual

LRACK - Limit Report Acknowledge Code

Format: B[1]

0 = Accepted

1 = Denied. Insufficient space

2 = Denied. Invalid format

3 = Denied. At least one CEID link already defined

4 = Denied. At least one CEID does not exist

5 = Denied. At least one RPTID does not exist

>5 = Other errors

6 - 63 reserved

used in: S2F36

LVACK - Variable limit definition acknowledge code

Format: B[1]

1 = Variable does not exist

2 = Variable has no limits capability

3 = Variable repeated in message

4 = Limit value error as desired in LIMITACK

5 - 63 reserved

used in: S2F46

MachineSide - Side of the machine

Format: U1

0 = right side in transport direction

1 = left side in transport direction

MaxBallDev - Maximal ball deviation

MaxBallDev is calculated by the vision system during the optical centering of a package

form. It is calculated over all balls in all ball groups.

Format: F8

Units are 1/1000 mm

used in: PLACEINFOx,

MaxLeadDev - Maximum lead deviation

MaxLeadDev is calculate by the vision system during the optical centering of a package

form. It is calculate over all leads in all lead groups.

Format: F8

Units are 1/1000 mm

used in: PLACEINFOx,

MAX_TIME_TO_STOP - amount of minutes of spooling until a Remote Stop (if

Safe_Spool_Mode is activ)

Format: U4

MDLN - Equipment Model Type

Format: A

used in: S1F2, S1F13, S1F14, S1F65, S1F66