00193786-02 - 第83页

S I P L A C E G EM S W V e r s i on G EM 505 . 03 SP 1 H O S T I n t e r f a c e M anua l ©S i e m en s A G, a ll r i gh t s r e s e r v ed page 83 o f 241 W i d t h i s r e t u r ned f r o m t he v i s i on s y s t e m …

100%1 / 241
SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual
Page 82 of 241 ©Siemens AG, all rights reserved
Format: I2
used in: PICKUPINFOx, PICKUPERRORSLOCx
tol_dirty_nozzle - vacuum value
Format: I4
Units are mbar
used in : VACUUMDATAx
tol_leaky_nozzle - vacuum value
Format: I4
Units are mbar
used in : VACUUMDATAx
TRID - Trace Request ID
Format: U4
used in: S2F23 S6F1
UNITS - Units of measure
Format: A
used in: S1F12, S2F30, S2F48
UPPERDB - Upper boundary of the dead-end of a limit
Format:
used in: S2F45, S2F48
Vacuum- Vacuum in the holding circuit.
Format: I4
Vacuum is the measured vacuum in the holding circuit.
Units are mbar
used in: PLACEINFOx, PICKUPINFOx,
VacuumErrors
Number of VacuumErrors.
Used in PICKUPERRORSLOCx (number of vacuum errors only after pickup)
VID - Variable ID
Format:
used in: S1F3, S1F11, S2F13, S2F15, S2F29, S2F30, S2F33, S2F45, S2F46, S6F3,
S6F13, S6F18, S6F22
VLAACK - Variable Limit Attribute Acknowledge Code
Format: B[1]
0 = OK
1 = Limit attribute definition error
2 = Cannot perform now
3 = Other error
4 - 63 reserved
used in: S2F46
Width- Width of a package form
SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual
©Siemens AG, all rights reserved page 83 of 241
Width is returned from the vision system. It’s the „optical“ width of the package form.
Units are 1/1000 mm
Format: U4
used in: PLACEINFOx
X-position - X-Coordinate of a placement or fiducial position
Format: U4
Units are 1/1000 mm
X-deviation - Deviation in X-direction
Format: I4
Units are 1/1000 mm
Y-position - Y-Coordinate of a placement or fiducial position
Format: U4
Units are 1/1000 mm
Y-deviation - Deviation in Y-direction
Format: I4
Units are 1/1000 mm
SIPLACE GEM SW Version GEM 505.03 SP1 HOST Interface Manual
Page 84 of 241 ©Siemens AG, all rights reserved
4.3 Stream 1
4.3.1 S1F1 - Are You There{XE "S1F1"}
S1F1 W. * H<->E
The Host may send this message to the Equipment at any time.
The SIPLACE sends this message periodically as a "heartbeat" to determine if the SECS
link is operational.
The Equipment Constant ConfigConnect can be set to cause the Equipment to send
S1F1 instead of S1F13 for Connect Request.
4.3.2 S1F2 - On Line Data (Equipment to Host)
{XE "S1F2"}S1F2 * H<-E
<L
<A {XE "MDLN"}MDLN> * MDLN Model Number
<A {XE "SOFTREV"}SOFTREV> * SOFTREV Software Revision
> .
The Equipment reports its Model Number and Software Revision.
4.3.3 S1F2 - On Line Data (Host to Equipment)
{XE "S1F2"}S1F2 * H->E
<L> .
4.3.4 S1F3 - Selected Status Request
{XE "S1F3"}S1F3 W * H-> E
<L
<U4 VID> * Variable ID
...
> .
The Host requests status from the SIPLACE. The Host sends the VIDs of interest.
Several VIDs can be specified if desired.
Normally, only VIDs of class SV (i.e. Status Variables) are used in this message.
However, the SIPLACE allows the Host to use any VID of class DV, EC, or SV.
If S1F3 contains a zero-length list, then the SIPLACE will report all variables of class SV,
in order by VID.