JUKI FX-3R MAINTENANCE GUIDE.pdf - 第248页

FX-3R Maintenance Guide 16-1 Rev. 1.00 [16] FX-3R JIG LISTS Part No. Part name Purpose Figure Remarks 40046647 JIG NOZZLE LNC Laser offset For LNC60 E51907290A0 CAL piece V Head offset Common for KE2000 series and KE700 …

100%1 / 251
FX-3R Maintenance Guide
15-13
15-5. Grease up
Use Alvania grease for all grease up locations.
1) Apply the grease to areas of 10 mm from both ends of the polished surface on the bottom of
the upper blade (See the figure below).
2) After the upper blade has been assembled, apply the grease to areas of 10 mm from both
ends of the bottom cutter blades L and R (see the figure below) and fill the holes A and B with
the grease.
3) Open and close the cutter blade several times and wipe off the grease sticking to a portion
other than the sliding part.
10
40084686
Upper blade
Rear
A
B
40084687
40084688
Bottom blades L and R
Figure 15-5-1 Grease Up Locations (1)
4) Adjust the pushing pressure of the fixed blade. (See page 1 of M11_TAPE_CUTTER in the
QA table.)
5) Apply the grease to the hatched portion at the center of the bottom blade (See the figure
below). After the grease has been applied, wipe off the grease so that the thin oil coat is
seen.
∗ Open and close the cutter several times. If the oil coat lines are seen, the amount of the
applied grease is excessive. Conversely, if no oil coat lines are seen, the amount of the
applied grease is insufficient.
6) Wipe off the grease sticking to a portion other than the sliding part.
Figure 15-5-2 Grease Up Locations (2)
40084687
40084688
ボトムブレード L、R
25
40084687
40084688
Bottom blades L and R
Rev. 1.00
FX-3R Maintenance Guide
16-1
Rev. 1.00
[16] FX-3R JIG LISTS
Part No. Part name Purpose Figure Remarks
40046647 JIG NOZZLE
LNC
Laser offset
For LNC60
E51907290A0 CAL piece V Head offset
Common for KE2000
series and KE700
series
40069017 OCC_FOCUS_
AJUST_JIG_
ASSY
OCC camera focus adjustment
Newly set for FX-3.
E2106998000 Camera
adjustment jig
OCC camera offset
Common for KE2000
series and KE700
series
E2107998000 Ceramic board
(2 inch)
Adjustment of OCC camera
illumination
Common for KE2000
series
40046648 ATC offset boss
70
ATC offset
(assembly position)
For KE2070
40035256 ATC height jig
ATC offset
(height position)
Common for KE2000
series
E2101998000 Jig nozzle A CVS offset
SOT inspect unit offset
Common for KE2000
series
40001343 Nozzle assembly
505
CVS height offset
Common for KE2000
series
40001346 Nozzle assembly
508
Laser offset
Head offset
ATC offset, etc.
Common for KE2000
series
FX-3R Maintenance Guide
16-2
Rev. 1.00
Part No. Part name Purpose Figure Remarks
E62607050A0A Master feeder
assembly
Pickup reference position offset
Same part as that used
for TF pick position
adjustment
40069368 X-MSC installation
jig
X-magnescale sticking jig
Newly set for FX-3.
40008106 MSC clearance jig For adjustment of magnet scale
detector head
T 0.25mm
T 0.35mm
T 0.45mm
40108676 X-frame support
jig
X-frame support part for roller
replacement
Newly set for FX-3R.
40108677 Roller support jig YS-linear base support part for
rail replacement
Newly set for FX-3R.