DT_ELMC-V3-EN_REV-B.1_L.pdf - 第51页

ELECTROVA P ® E LMC 51 6.4 WATER INLET VALVE Maintenanc e of th e water i nlet valv e i s to be d one after the fi rst 50 hours o f operat ion. Thereafter, twice a year (minimum). • Switch the appliance off. • Switch off…

100%1 / 56
ELECTROVAP® ELMC
50
6.3 DRAIN VALVE
The drain valve should be maintained whenever the steam tank is maintained or changed.
• Once the tank is out of the humidifier, disconnect the drain valve supply cables (Item 1).
• Unscrew the nut and the plastic protection of the supply coil (Item 2 & 3).
• Now you can remove the coil (Item 4) from the valve body (Item 5).
• Use a pair of pliers or a 19" wrench to unscrew the valve plug (Item 6) from the valve body (Item 5).
• Check and clean, if necessary, the inside of the valve body by running water through the hole.
Reassemble the drain valve as original, before repositioning the tank, by proceeding as follows:
1. Position the tank bottom in the valve connection, push down.
2. Replace the steam hose and do not forget to tighten the hose clamp.
Ensure that all the clamps are properly tightened whenever the humidifier is maintained.
6
Fig. 6-3. Humidifier drain valve
ELECTROVAP® ELMC
51
6.4 WATER INLET VALVE
Maintenance of the water inlet valve is to be done after the first 50
hours of operation. Thereafter, twice a year (minimum).
• Switch the appliance off.
• Switch off the water supply to the humidifier and unscrew the
water supply hose.
• Disconnect the power cables from the water inlet valve of your
humidifier (Item 1).
• Loosen the clamp and remove the water supply hose. (Item 2)
• Unscrew the two screws securing the valve (Item 3).
• Pull out your valve, remove the filter with pliers and remove the
coil (Item 4) by prying it off with a screwdriver.
• Run water through the valve body and over the filter to remove
any particles.
Once all these operations completed, please reassemble the unit, taking care to check the condition of the water
supply hose clamp. You can put your appliance back into service.
Ensure that all the clamps are properly tightened whenever the humidifier is maintained.
Fig. 6-4. Humidifier water inlet valve
ELECTROVAP® ELMC
52
7 SPARE PARTS
7.1 HYDRAULIC PART
N°
Code
Description
1
D110136-SC-SP
Complete filling cup for 1 SC
D110136-MC-SP
Full filling cup for 1 MC
2
D110146-SP
Tightening clamp - 12x22mm
D110139-SP
Tightening clamp - 16x27mm
D110140-SP
Tightening clamp - 20x32mm
D110141-SP
Tightening clamp - 25x40mm
D108256-SP
Tightening clamp - 40x60mm
4
D110195-SP
Cylinder maintenance kit for 1 SC
D110196-SP
Cylinder maintenance kit for 1 MC
5
D61898
Pipe - 13/19mm (water supply hose)
D61899
Pipe - 19/26mm (overflow and cylinder filling hoses)
6
D110157-SP
Water inlet valve ELMC 5-30
D110771-SP
Water inlet valve ELMC 40-90
7
D110154-SP
Drain cup (upper part)
D110154-SP
Drain cup (lower part)
8
D116726-24-SP
Complete drain valve 24V
D110148-24-SP
Operator with 24V coil for drain valve
D110149-SP
Drain valve body
D116656-24-SP
Drain valve coil 24V
D110153-SP
Bag of 10 drain valve gaskets
9
D119698-1SC-SP
3-cable cylinder 1 SC power kit
D119698-1MC-SP
3-cable cylinder 1 MC power kit
D119698-2MC-SP
3-cable cylinder 2 MC power kit
D119698-3MC-SP
3-cable cylinder 3 MC power kit
10
D119699-1SC-SP
1 SC High Level Electrode Cables
D119699-1MC-SP
1MC High Level Electrode Cables
D119699-2MC-SP
2MC High Level Electrode Cables
D119699-3MC-SP
3MC High Level Electrode Cables
(*)
SC = Small Cylinder - MC= Medium Cylinder