KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第1019页

214 ① T he sens itivity of the STOP sens or m ay be too low. Please re-adjust the sensitivity of the sensor, us ing the volum e control k nob attached to the sensor. ② If the treatm ent1 does not work, there is a possibi…

213

E650224 “PW Conveying Error : PWB conveying time out error of Input

buffer. The process is forcibly terminated. Please remove on the

conveying route”

[Cause] Since IN sensor detected a PWB coming in, the belt of the INPUT buffer got

started to drive and the PWB was taken in to the INPUT buffer. However, the IN

sensor did not get OFF after a certain amount of time has passed. Usually, this

error occurs when a PWB can not go through the INPUT buffer for some reason.

[Treatment] 1 If the PWB was on the position where it is detected by IN and WAIT sensors

when the error occurred.

The PWB can not move for it got caught on the conveyor for some reason.

① The conveyor width is not matching the PWB width. Please re-adjust the

conveyor width.

② The PWB you are trying to convey does not match the specifications of

your machine. The following cases do not match your machine.

• A PWB with thickness of 0.3mm or less. Or a PWB with thickness of

4mm or more.

• A PWB with mass of 2kg or more.

2 If the PWB overran the WAIT station and got conveyed to the center station

when the error occurred.

The WAIT sensor is not detecting the PWB. Please select [Manual Control]

from the menu bar, and then select [Control(C)] [Conveyor(C)] [Independent

Control of Conveyor(I)] to see the status of WAIT sensor in the ‘Status’ frame.

① There is a possibility that the WAIT sensor is broken. It could be that the

wiring came out of the connector part, that a contact pin of the connector

part is broken, that wiring got cut off, or that sensor itself is broken.

Please examine the wiring and the connector. If any of them are broken,

you need to replace them with the new ones.

② If the treatment1 does not work, PCB is broken or the wiring between the

PCBs is bad.

E650234 “PWB Conveying Error : PWB conveying time out error of the center

station. The process is forcibly terminated. Please remove on the

conveying route”

[Cause] When inletting a PWB from the Input buffer to the center station, STOP sensor

did not get ON even though a certain amount of time has passed since the WAIT

sensor of the Input buffer got OFF. Usually, this error occurs when a PWB can

not go through the INPUT buffer for some reason.

[Treatment] 1 If the PWB was NOT on the position where it is detected by WAIT and STOP

sensors when the error occurred.

The PWB can not move for it got caught on the conveyor for some reason.

① The conveyor width is not matching the PWB width. Please re-adjust the

conveyor width.

② The PWB you are trying to convey does not match the specifications of

your machine. The following cases do not match your machine.

• A PWB with thickness of 0.3mm or less. Or a PWB with thickness of

4mm or more.

2 If the belt was moving for a while after the PWB touched the stopper when the

error occurred.

The STOP sensor is not detecting the PWB. Please select [Manual Control]

from the menu bar, and then select [Control(C)] [Conveyor(C)] [Independent

Control of Conveyor(I)] to see the status of STOP sensor in the ‘Status’ frame.

214

① The sensitivity of the STOP sensor may be too low. Please re-adjust the

sensitivity of the sensor, using the volume control knob attached to the

sensor.

② If the treatment1 does not work, there is a possibility that the STOP

sensor is broken. It could be that the wiring came out of the connector

part, that a contact pin in the connector part is broken, that wiring got cut

off, or that sensor itself is broken. Please examine the wiring and the

connector. If any of them are broken, you need to replace them with the

new ones.

③ If the treatment2 does not work, PCB is broken or the wiring between the

PCBs is bad.

E650242 “PWB Conveying Error : PWB conveying error of the center station

on the Entrance side. The process is forcibly terminated. Please

remove on the conveying route”

[Cause] This error occurs if the STOP sensor on the center station on the Entrance side

got OFF then ON again, but it does not get OFF even if a certain amount of time

has passed since it got ON again when conveying a PWB on the center station

on the Entrance side to the center station on the Exit side.

[Treatment] 1 The PWB was on the position where it is detected by STOP sensor on the

center station on the Entrance side when the error occurred.

The PWB can not move for it got caught on the conveyor for some reason.

① The conveyor width is not matching the PWB width. Please re-adjust the

conveyor width.

② The PWB you are trying to convey does not match the specifications of

your machine. The following cases do not match your machine.

• A PWB with thickness of 0.3mm or less. Or a PWB with thickness of

4mm or more.

• A PWB with mass of 2kg or more.

2 The PWB was NOT on the position where it is detected by STOP sensor on

the center station on the Entrance side when the error occurred.

If the STOP sensor does not get OFF when a PWB is properly being

conveyed, there is a possibility that the sensor is detecting something else.

Please select [Manual Control] from the menu bar, and then select

[Control(C)] [Conveyor(C)] [Independent Control of Conveyor(I)] to see the

status of STOP sensor on the center station on the Entrance side in the

‘Status’ frame.

① The sensitivity of STOP sensor may be too high. Please adjust it, using

the volume control knob attached to the sensor.

② If the treatment1 does not work, there is a possibility that the STOP

sensor is broken, It could be that the wiring came off the connector part,

that a contact pin in the connector part is broken, that wiring got cut off, or

that sensor itself is broken. Please examine the wiring and the connector.

If any of them are broken, you need to replace them with new ones.

③ If the treatment2 does not work, a PCB is broken or the wiring between

the PCBs is bad.

215

E650243 “PWB Conveying Error : PWB conveying error of the center station

on the Entrance side. The process is forcibly terminated. Please

remove on the conveying route”

[Cause] This error occurs if the C-OUT sensor on the center station on the Entrance side

got OFF then ON again, but it does not get OFF even if a certain amount of time

has passed since it got ON again when conveying a PWB on the center station

on the Entrance side to the center station on the Exit side.

[Treatment] 1 The PWB was on the position where it is detected by C-OUT sensor on the

center station on the Entrance side when the error occurred.

The PWB can not move for it got caught on the conveyor for some reason.

① The conveyor width is not matching the PWB width. Please re-adjust the

conveyor width.

② The PWB you are trying to convey does not match the specifications of

your machine. The following cases do not match your machine.

• A PWB with thickness of 0.3mm or less. Or a PWB with thickness of

4mm or more.

• A PWB with mass of 2kg or more.

2 The PWB was NOT on the position where it is detected by C-OUT sensor on

the center station on the Entrance side when the error occurred.

If the C-OUT sensor does not get OFF when a PWB is properly being

conveyed, there is a possibility that the sensor is detecting something else.

Please select [Manual Control] from the menu bar, and then select

[Control(C)] [Conveyor(C)] [Independent Control of Conveyor(I)] to see the

status of STOP sensor on the center station on the Entrance side in the

‘Status’ frame.

① The sensitivity of C-OUT sensor may be too high. Please adjust it, using

the volume control knob attached to the sensor.

② If the treatment1 does not work, there is a possibility that the C-OUT

sensor is broken, It could be that the wiring came off the connector part,

that a contact pin in the connector part is broken, that wiring got cut off, or

that sensor itself is broken. Please examine the wiring and the connector.

If any of them are broken, you need to replace them with new ones.

③ If the treatment2 does not work, a PCB is broken or the wiring between

the PCBs is bad.

E650244 “PWB Conveying Error : PWB conveying time out error of the center

station on the Entrance side. The process is forcibly terminated.

Please remove on the conveying route”

[Cause] This error occurred because the STOP sensor on the center station on the

Entrance side did not get ON even though a certain amount of time has passed

since the WAIT sensor on the Input buffer got OFF when conveying a PWB on

the Input buffer to the center station on the Entrance side. Usually, this error

occurs when a PWB can not go through the INPUT buffer for some reason.

[Treatment] 1 The PWB was on the position where it is NOT detected by WAIT sensor or

STOP sensor on the center station on the Entrance side when the error

occurred.

The PWB can not move for it got caught on the conveyor for some reason.

① The conveyor width is not matching the PWB width. Please re-adjust

the conveyor width.

② The PWB you are trying to convey does not match the specifications

of your machine. The following cases do not match your machine.