KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第1130页
47 [Treatm ent] Please check and s ee if the axis can m ove proper ly with Manual control. E240001 “The axis cannot be moved to escape point” [Cause] You could not m ove the axis to the Escape point. [Treatm ent] Please …
46
E191103 “Failed to automatically learn the recognition conditions of template.
Details : %d Please modify the conditions and teach again”
[Cause] Please refer to
ＸＸＸＸＸＸ
.
Some program versions are clashing with each other.
[Treatment] Please re-install or version-up the application.
Please re-start your machine.
Q191300 “There is a similar pattern in the upper part of the template. Would
you like to take the teaching results in?”
[Cause] The user defined template has a similar patter in the upper part of the template.
[Treatment] Please re-teach other user defined templates to the machine.
If you do not have other user defined templates, current template will be taken in
although the template may not be recognized correctly.
Q191301 “There is a similar pattern in the lower part of the template. Would
you like to take the teaching results in?”
[Cause] The user defined template has a similar patter in the upper part of the template.
[Treatment] Please re-teach other user defined templates to the machine.
If you do not have other user defined templates, current template will be taken in
although the template may not be recognized correctly.
Q191302 “There is a similar pattern on the left side of the template. Would
you like to take the teaching results in?”
[Cause] The user defined template has a similar patter on the left side of the template.
[Treatment] Please re-teach other user defined templates to the machine.
If you do not have other user defined templates, current template will be taken in
although the template may not be recognized correctly.
Q191303 “There is a similar pattern on the right side of the template. Would
you like to take the teaching results in?”
[Cause] The user defined template has a similar patter on the right side of the template.
[Treatment] Please re-teach other user defined templates to the machine.
If you do not have other user defined templates, current template will be taken in
although the template may not be recognized correctly.
Q191304 “The template does not have enough contrast. Would you like to
take the teaching results in?”
[Cause] The user defined template does not have enough contrast.
[Treatment] Please re-teach other user defined templates to the machine.
If you do not have other user defined templates, current template will be taken in
although the template may not be recognized correctly.
Q191305 “The template has no features. Would you like to take the teaching
results in?”
[Cause] The specified user defined template does not have any notable patterns.
[Treatment] Please re-teach other user defined templates to the machine.
If you do not have other user defined templates, current template will be taken in
although the template may not be recognized correctly.
E240000 “The axis cannot be moved”
[Cause] The axis could not move for some reason.
47
[Treatment] Please check and see if the axis can move properly with Manual control.
E240001 “The axis cannot be moved to escape point”
[Cause] You could not move the axis to the Escape point.
[Treatment] Please check and see if the axis can move properly with Manual control.
E240002 “Yc table cannot be moved”
[Cause] You could not move the Yc table.
[Treatment] Please check and see if the Yc table can move properly with Manual control.
E240003 “The axis margin out of range. It is not possible to operation”
[Cause] You could not move the axis since it went out of its movable range.
[Treatment] Please check and see if its coordinates are correct.
E240004 “The interrupt which was not able to operate was detected. The
trace is ended”
[Cause] The process was forcibly aborted since an interruption, such as axis alarm and
Emergency STOP, that stops every kind of actions was detected.
[Treatment] Please check and see if any alarms occurred, and deal with causes of the alarm.
E240005 “The area sensor was detected.
Please remove the sensor
reaction factor”
[Cause] Tracing got paused since the area sensor detected something.
[Treatment] Please removed a factor detected by the sensor, and resume tracing.
E240006 “The feeder float sensor was detected. Please remove the sensor
reaction factor”
[Cause] Tracing got paused since the feeder float sensor detected something.
[Treatment] Please removed a factor detected by the sensor, and resume tracing.
E240007 “Input is mistake”
[Cause] Something was wrong with the characters when you hit Enter key to define
characters.
[Treatment] Please re-enter characters
E240008 “There is no data previous”
[Cause] This error occurs when there is no data ahead to trace.
[Treatment] Check only
E240009 “There is no data next”
[Cause] This error occurs when there is no data behind to trace.
[Treatment] Check only
E240010 “Specified device cannot be used”
[Cause] The specified device is set to “not use” in the Use unit in Setup.
[Treatment] If the device is available, please set it to “use” in the Use unit in Setup. If not, this
procedure cannot be executed.
48
E240011 “The station is different”
[Cause] This error occurs when the side the HOD device is on is wrong when teaching.
[Treatment] Please check and see which device (left or right) to use.
E240012 “Specified position not move”
[Cause] You could not move the axis to the specified position since the axis went out of its
movable range.
[Treatment] Please check and see if the coordinates are correct.
E240013 “The origin point return is non-completion”
[Cause] Home returning has not been complete yet.
[Treatment] Please hit the ORIGIN button to perform the Home returning, and try the process
again.
E240014 “The Left OCC device is set in unused by the setup”
[Cause] The Left OCC device is set to “not use” in the Use unit in Setup.
[Treatment] If the device is available, please set it to “use” in the Use unit in Setup. If not, this
procedure cannot be executed.
E240015 “The Right OCC device is set in unused by the setup”
[Cause] The Right OCC device is set to “not use” in the Use unit in Setup.
[Treatment] If the device is available, please set it to “use” in the Use unit in Setup. If not, this
procedure cannot be executed.
E240016 “The HMS device is set in unused by the setup”
[Cause] The HMS device is set to “not use” in the Use unit in Setup.
[Treatment] If the device is available, please set it to “use” in the Use unit in Setup. If not, this
procedure cannot be executed.
Q240500 “End tracking?”
[Cause] You are asked if to end the tracking process.
[Treatment] If you want to end the process, press ‘Yes’. If not, press ‘No’.
E241000 “Memory allocation error”
[Cause] Failed to save the work area necessary to run a program or to create a window
due to the shortage of memory
[Treatment] Please increase some memory available by exiting unnecessary applications.