KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第1169页

86 E501999 “Abnormal stop <%s> [Cause] T his er ror occ urs when an action does not end norm ally. ? : An action that was taking plac e when a production ended abnorm ally. W hile transpor ting PW Bs W hile recogni…

100%1 / 1361
85
E500605 “An error occurred when disposing a component”
[Cause] This error occurs if the component present check at a component disposal action
gets an error when starting a production.
[Treatment] Pressing OK button will abort the process. In this case, the production will not be
executed.
E500700 “An error occurred while Auto. PWB Width Alignment Control. The
process gets discontinued”
[Cause] This error occurs if an error occurs or an action did not take place properly while
Auto. PWB Width Alignment Control.
[Treatment] Pressing OK button will abort the process. If a particular reason (Home returning
has not been complete, etc.) why Auto. PWB Width Alignment Control can not be
executed is given, please perform any means to get rid of the factor that stops
Auto. PWB Width Alignment Control. If any particular reasons are not given,
please, check the action of Auto. PWB Width Alignment Control by Manual
control .
E500701 “Para error. PWB Width Alignment Control occurred”
[Cause] This error occurred if an entered value to be defined by Enter key is wrong when
performing Auto. PWB Width Alignment Control.
[Treatment] Please check the entered value.
E500800 “A PWB is detected within the conveyors of both stations. Please
remove the PWB”
[Cause] The production can not get started because PWBs are on the conveyors on both
sides when starting the production.
[Treatment] Please remove the PWBs from the conveyors by pressing OK button, and then
press START key again.
E500801 “A PWB is detected within the conveyor of the Left station. Please
remove the PWB”
[Cause] The production can not get started because a PWB is on the conveyor on left
side when starting the production.
[Treatment] Please remove the PWBs from the conveyors by pressing OK button, and then
press START key again.
E500802 “A PWB is detected within the conveyor of the Right station. Please
remove the PWB”
[Cause] The production can not get started because a PWB is on the conveyor on right
side when starting the production.
[Treatment] Please remove the PWBs from the conveyors by pressing OK button, and then
press START key again.
86
E501999 “Abnormal stop <%s>
[Cause] This error occurs when an action does not end normally.
? : An action that was taking place when a production ended abnormally.
While transporting PWBs
While recognizing VCS
While recognizing
IC marks
While recognizing BOC marks
While detecting bad marks
Placement position
Pick position
While recognizing L3
While installing a nozzle on a head
While returning a nozzle to ATC
While disposing a component
While reading bank marks
Other positions
[Treatment] A detailed error message should have been shown prior to this message.
Please check and see the status, using the given error number.
E500900 “The connection with HLC is on-line. The production is not available
with the currently selected production program created by the
machine”
[Cause] The connection between your machine and HLC is set to ON in the Setup. The
currently selected production program was created by the machine. Therefore, its
production can not get started.
[Treatment] Please cut off the connection between your machine and HLC in the Setup or
read in another production program.
E500901 “It is not connected to HLC. The production is not available with the
currently selected production program created by HLC”
[Cause] A production program that was created by HLC was read in and its production is
about to get started with the connection between your machine and HLC being
OFF.
[Treatment] Please enable the connection between your machine and HLC in the Setup or
read in another production program.
E500902 “Online switch is not effective to the Setup data though the
connection with HLC is turning on”
[Cause] Online switch is not available while the connection between your machine and
HLC is ON in the Setup data.
[Treatment] Please cut off the connection between your machine and HLC in the Setup or
enable the online switch.
E501000 “MTC Move Failed”
[Cause] This error occurs when an error occurs from MTC during a production.
[Treatment] Please turn off the power supply of MTC and examine it.
87
E501010 “MTC Power is Off. Please Power On”
[Cause] This error occurs if MTC is not ON when starting a production.
[Treatment] Please turn on the power supply of MTC and press OK button. Pressing Cancel
button will have you back to the status that is before pressing START key.
E501011 “MTC Emergency Switch is Pressed. Please Release the Switch”
[Cause] This error occurs if the Emergency Switch of MTC has been pressed when
starting a production.
[Treatment] Please press OK button after disabling the Emergency Switch. Pressing Cancel
button will have you back to the status that is before pressing START key.
E501012 “MTC is No Original”
[Cause] This error occurs if MTC Home returning has not been complete yet when
starting a production.
[Treatment] OK button : Performs MTC Home returning.
Cancel button : Will have you back to the status that is before pressing START
key.
E501013 “MTC is Off-Line Condition. Please change to On-Line”
[Cause] This error occurs if MTC is Offline when starting a production.
[Treatment] Please put MTC in online status and press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501014 “MTC is Door Open Condition. Please Close Cover”
[Cause] This error occurs if MTC door is open when starting a production.
[Treatment] Please close the MTC door then press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501015 “MTC is Cover Open Condition. Please Close Cover”
[Cause] This error occurs if MTC cover is open when starting a production.
[Treatment] Please close the MTC cover then press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501016 “MTC is Error Condition”
[Cause] This error occurs if MTC is in an error status when starting a production.
[Treatment] Please turn off the power supply of MTC and examine it.
E501017 “MTC is Change Component Condition. Please Release the Change
Condition”
[Cause] This error occurs if MTC is in a status where MTC needs a component change
when starting a production.
[Treatment] Please disable the status of MTC, and press OK button.