KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第1171页

88 E501018 “Component exi sts on the M TC Shuttle. Please Remove Component from Shuttl e” [Cause] T his er ror occ urs if any components ar e on the shuttle of MT C when starting a production. [Treatm ent] Pleas e rem ov…

100%1 / 1361
87
E501010 “MTC Power is Off. Please Power On”
[Cause] This error occurs if MTC is not ON when starting a production.
[Treatment] Please turn on the power supply of MTC and press OK button. Pressing Cancel
button will have you back to the status that is before pressing START key.
E501011 “MTC Emergency Switch is Pressed. Please Release the Switch”
[Cause] This error occurs if the Emergency Switch of MTC has been pressed when
starting a production.
[Treatment] Please press OK button after disabling the Emergency Switch. Pressing Cancel
button will have you back to the status that is before pressing START key.
E501012 “MTC is No Original”
[Cause] This error occurs if MTC Home returning has not been complete yet when
starting a production.
[Treatment] OK button : Performs MTC Home returning.
Cancel button : Will have you back to the status that is before pressing START
key.
E501013 “MTC is Off-Line Condition. Please change to On-Line”
[Cause] This error occurs if MTC is Offline when starting a production.
[Treatment] Please put MTC in online status and press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501014 “MTC is Door Open Condition. Please Close Cover”
[Cause] This error occurs if MTC door is open when starting a production.
[Treatment] Please close the MTC door then press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501015 “MTC is Cover Open Condition. Please Close Cover”
[Cause] This error occurs if MTC cover is open when starting a production.
[Treatment] Please close the MTC cover then press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501016 “MTC is Error Condition”
[Cause] This error occurs if MTC is in an error status when starting a production.
[Treatment] Please turn off the power supply of MTC and examine it.
E501017 “MTC is Change Component Condition. Please Release the Change
Condition”
[Cause] This error occurs if MTC is in a status where MTC needs a component change
when starting a production.
[Treatment] Please disable the status of MTC, and press OK button.
88
E501018 “Component exists on the MTC Shuttle. Please Remove Component
from Shuttle”
[Cause] This error occurs if any components are on the shuttle of MTC when starting a
production.
[Treatment] Please remove those components from the MTC shuttle and press OK button.
E501019 “Because MTC is Change Component Condition, home position
return cannot be done. Please Release the Change condition”
[Cause] This error occurs if MTC is in a status where MTC needs a component change
when performing the Home returning of MTC.
[Treatment] Please disable the status of MTC, and press OK button.
E501100 “MTS power off”
[Cause] MTS was not ON when starting a production.
[Treatment] Please turn on the power supply of MTS and press OK button. Pressing Cancel
button will have you back to the status that is before pressing START key.
E501101 “MTS offline”
[Cause] MTS was not online when starting a production.
[Treatment] Please put MTC in online status and press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501102 “MTS cannot move because of cover opening”
[Cause] MTS cover was open when starting a production.
[Treatment] Please close the MTS cover and press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501103 “The door of MTS opens”
[Cause] MTS door was open when starting a production.
[Treatment] Please close the MTS door and press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
E501200 “Communication error of DTS occurred”
[Cause] An error occurred in DTS.
[Treatment] This is a DTS internal error. Please take a note of the error number and contact
our technical service dept. for information.
E501201 “DTS status got an error. The process can not be performed”
[Cause] This error occurs if DTS is in an error status when starting a production.
[Treatment] Please turn off the power supply of DTS and examine it.
E501202 “DTS’ cover is open. Please close the cover”
[Cause] This error occurs if DTS cover is open when starting a production.
[Treatment] Please close the DTS door and press OK button. Pressing Cancel button will
have you back to the status that is before pressing START key.
89
E501203 “DTS is not in the executable status. Would you like to have DTS
return to Home position?”
[Cause] This error occurs if DTS Home returning has not been complete when starting a
production.
[Treatment] OK button : Performs DTS Home returning.
Cancel button : Will have you back to the status that is before pressing START
key.
E501204 “DTS is not in the executable status. Would you like to have DTS
return to Home Position?”
[Cause] This error occurs if DTS is in the executable status when starting a production.
[Treatment] OK button : Performs Home returning.
Cancel button : Will have you back to the status that is before pressing START
key.
E501205 “DTS is in the supplying status. Please release DTS from the status”
[Cause] This error occurs if DTS is in the supplying status when starting a production.
[Treatment] Please disable the supply status of DTS and press OK button. Pressing Cancel
button will have you back to the status that is before pressing START key.
E501300 “No tracing data”
[Cause] This error occurs if there is not data to trace on the specified station when
executing tracing.
[Treatment] Please press OK button to continue the process.
E501400 “[Vision] Memory access error”
[Cause] There is not enough memory.
[Treatment] Please re-start the application.
E501401 “[Vision] Failed to collect System condition data”
[Cause] The system information is wrong.
[Treatment] Please re-boot your machine.
E501402 “[Vision] Failed to collect Mark recognition condition data”
[Cause] The entered mark data is not correct.
[Treatment] Please go to the Production Program Editor and check the mark data.
E501403 “[Vision] Failed to collect Component recognition condition data”
[Cause] The entered vision data is not correct.
[Treatment] Please go to the Production Program Editor and check the mark data.
E501404 “[Vision] Failed to transmit System condition data to the Vision
board”
[Cause] The system information is wrong.
[Treatment] Please re-boot your machine.
E501405 “[Vision] Failed to transmit Bankmark recognition condition data to