KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第1284页
201 E631011 “ViRecog Error: The mark is touching the frame. Please examine Mark data ” [Cause] T he actual m ar k c oordinates are dif fer ent from that in the data. The ref . pin is not in the r ef. hole pr operly. A wr…
200
[Treatment] Please re-install or version up the application.
Please re-boot your machine.
Please contact our technical service dept. for information.
E630217 “Vision System: It is unprescribed ERR code. ERR17 code”
[Cause] Unprescribed error response was sent back from VCS.
Some program versions are clashing with each other.
[Treatment] Please re-install or version up the application.
Please re-boot your machine.
Please contact our technical service dept. for information.
E630218 “Vision System: It is unprescribed ERR code. ERR18 code”
[Cause] Unprescribed error response was sent back from VCS.
Some program versions are clashing with each other.
[Treatment] Please re-install or version up the application.
Please re-boot your machine.
Please contact our technical service dept. for information.
E630219 “Vision System: It is unprescribed ERR code. ERR19 code”
[Cause] Unprescribed error response was sent back from VCS.
Some program versions are clashing with each other.
[Treatment] Please re-install or version up the application.
Please re-boot your machine.
Please contact our technical service dept. for information.
E630300 “ViLib Thread: Other illogical matter occurred”
[Cause] An unexpected error occurred in the vision device driver.
[Treatment] Please re-boot your machine.
E630301 “ViLib Thread: Turnaround time-out occurred”
[Cause] There is no response from VCS.
[Treatment] Please re-boot your machine.
E631010 “ViRecog Error: No mark can be found. Please examine the PWB”
[Cause] The actual mark coordinates are different from that in the data.
There is no mark on the board.
The ref. pin is not in the ref. hole properly.
A wrong board was loaded.
The light is not ON.
[Treatment] Please re-teach the marks to the machine.
Please re-load a PWB.
Please re-load the production program.
Please examine if the light gets ON properly.
201
E631011 “ViRecog Error: The mark is touching the frame. Please examine
Mark data”
[Cause] The actual mark coordinates are different from that in the data.
The ref. pin is not in the ref. hole properly.
A wrong board was loaded.
[Treatment] Please re-teach the marks to the machine.
Please re-load a PWB.
Please re-load the production program.
Please examine if the light gets ON properly.
E631012 “ViRecog Error: The consistency of the marks is too low. Please
examine the PWB”
[Cause] The actual mark coordinates are different from that in the data.
There is no mark on the board.
The marks are critically dirty.
The ref. pin is not in the ref. hole properly.
A wrong board was loaded.
The light is not ON.
[Treatment] Please examine the board.
Please re-load a PWB.
Please examine the marks.
Please re-teach the marks to the machine.
Please re-load the production program.
Please examine if the light gets ON properly.
E631013 “ViRecog Error: Other mark recognition error occurred. Please
examine the mark data”
[Cause] The actual mark coordinates are different from that in the data.
There is no mark on the board.
The marks are critically dirty.
The ref. pin is not in the ref. hole properly.
A wrong board was loaded.
The light is not ON.
An unprescribed error was sent back from VCS.
Some program versions are clashing with each other.
[Treatment] Please examine the board.
Please re-load a PWB.
Please examine the marks.
Please re-teach the marks to the machine.
Please re-load the production program.
Please examine if the light gets ON properly.
Please re-install or version up the application.
Please re-boot your machine.
Please contact our technical service dept. for information.
E631020 “ViRecog Error:
The lead is bent. Please examine the component”
[Cause] The lead is bent.
The lead-bent detecting level is too low.
The light is either too bright or too dark.
The light is dirty.
The camera lens is dirty.
The camera cable almost gets cut off.
The light cable almost gets cut off.
The brilliancy of LED is varying.
[Treatment] Please raise the lead-bent detecting level in the production program.
Please examine the light parameter in the production program.
202
Please adjust the light parameter in the production program.
Please clean the light.
Please clean the camera lens.
Please change the camera cables.
Please change the light cables.
Please re-adjust the electric currency of the light.
Please change the lights and re-adjust the electric currency of the new light.
Please change the light boards and re-adjust the electric currency of the new
board.
E631021 “ViRecog Error: The position of the lead tip is illegal. Please
examine the component”
[Cause] The leads are irregular in length.
The lead is too dark.
The light is either too bright or too dark.
The light is dirty.
The camera lens is dirty.
The light cable almost gets cut off.
The brilliancy of LED is varying.
[Treatment] Please examine the light parameter in the production program.
Please adjust the light parameter in the production program.
Please clean the light.
Please clean the camera lens.
Please change the light cables.
Please re-adjust the electric currency of the light.
Please change the lights and re-adjust the electric currency of the new light.
Please change the light boards and re-adjust the electric currency of the new
board.
E631022 “ViRecog Error: Lead pitch is wrong. Please examine Vision data”
[Cause] The component’s lead pitch is different.
The light is either too bright or too dark.
The light is dirty.
The camera lens is dirty.
The light cable almost gets cut off.
The brilliancy of LED is varying.
[Treatment] Please examine the lead pitch in the production program.
Please examine the light parameter in the production program.
Please adjust the light parameter in the production program.
Please clean the light.
Please clean the camera lens.
Please change the light cables.
Please re-adjust the electric currency of the light.
Please change the lights and re-adjust the electric currency of the new light.
Please change the light boards and re-adjust the electric currency of the new
board.