KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第130页
4 − 23 The placement data you selected is pasted onto t he line whose number you specified. Y ou can execute t he paste operat ion only once (the data will be erased fr om the mem ory buffer aft er you perf orm the past …
4 − 22
4.3 Editing
When you select the [Edit] command on the menu bar, the following commands menu
appears on the screen.
Selecting the range of data
To cut or copy data, select the data range to be copied or cut in advance.
When you drag the trackball, the lines to be selected are highlighted.
When you press the up or down arrow key while holding the SHIFT key of a keyboard,
the lines to be selected are highlighted.
Every time you press the Page UP key or Page Down key while holding down the
SHIFT key, a page (lines displayed on the screen) is selected one by one
sequentially.
4.3.1 Cut
This command deletes one line or multiple lines already selected. After deleting a
line or lines, lines after the deleted line(s) are scrolled up and displayed automatically.
If any line is not selected, you cannot select this command.
When you select all of placement data associated with the certain component data,
and select this [Cut] command, the following inquiry message appears on the screen.
4.3.1.1 When you select the <YES> button
The dialog box appears that allows you to specify the destination line number as
shown below.
4 − 23
The placement data you selected is pasted onto the line whose number you
specified. You can execute the paste operation only once (the data will be erased
from the memory buffer after you perform the paste operation).
When you click the <CANCEL> button, the system will execute neither the cut nor
paste operation.
4.3.1.2 When you select the <NO> button
The system deletes the placement data and component data. Note that the
placement data is loaded to the memory buffer and you can paste it, but you cannot
paste any component data.
Assume that component “a” is associated with placements “a1” and “a2,” and component “b”
with “b1,” “b2” and “b3.”
Note: If you use database, the deleted component data may seem to be pasted. However,
this is not pasted, but the corresponding component data is called from the database.
4.3.2 Copy
This command loads the data which is selected and highlighted into the memory
buffer. To paste it in another data, execute the [Paste] command.
Descri
p
tion
:
Select placements as shown in the left
figure. This means the selection of:
- all the placements associated with
component “a” (“a0” and “a1”), and
- part of placements with “b” (“b0” from
amon
g
“b0
,
” “b1” and “b2”
)
.
Cut placement
data “b0,” “a1”
and “a0.”
When the [Cut] command is executed
in this condition, the system cuts the
selected placement records, and the
component record for “a.” Component
“a” is deleted since all the placements
associated with it (“a0” and “a1”) are
cut.
Deleted
component “a.”
Pasted
placements
“b0,” “a1” and
“a0.”
You can paste the placement records
you cut by selecting [Paste] (see the
left figure).
However, the data for component “a”
will be incomplete, registered only by
the component name.
4 − 24
4.3.3 Paste
This command inserts the data which was cut or copied into the memory buffer at or
before which the cursor is located.
After you select the [Cut] command, the following dialog box appears on the screen.
When you specify the “X pitch” and “Y pitch”, you can execute the incremental copy
function which copies data with adding or subtracting the specified values to/from
the X placement position and Y placement position.
After executing the [Paste] function for Placement data, all of the component IDs are
set to “#” and data is pasted.
If there is no data in the memory buffer, this command is disabled.
① No. of copies: Specifies the number of times for copying data. The default
value is “1”.
② X pitch: Specifies the amount to increment or decrement the placement
position in the X direction. The default value is “0.00”.
③ Y pitch: Specifies the amount to increment or decrement the placement
position in the Y direction. The default value is “0.00”.
④ OK: Executes the “Paste” command.
⑤ Cancel: Cancels the “Paste” command.
Example of the paste result
When normally executed
例
)
Component IDs X Y Angle Component name
R1 5.00 10.00 45.00 1608-A
R2 10.00 10.00 0.00 1608-A
No. of copies 3 X Pitch: 0.50
Y Pitch: 1.00
# 5.50 11.00 45.00 1608-A
# 10.50 11.00 0.00 1608-A
# 6.00 12.00 45.00 1608-A
# 11.00 12.00 0.00 1608-A
# 6.50 13.00 45.00 1608-A
# 11.50 13.00 0.00 1608-A
• The copied block is inserted above the specified line.
• All of the Component IDs are set to “#”.
• The input focus is located at the first inserted Component ID.