KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第1333页

250 E690028 “Resist ance can no be measured. Please check i f probe shuts dow n properly” [Cause] T he tester overflowed data when meas uring the res istance. • The objec t(com ponent) of the m easurem ent is not contact…

100%1 / 1361
249
E690023 “Something is wrong with the measured volume”
[Cause] The condenser capacity gotten from the tester is irregular.
• The object(component) of the measurement is not contacting the probe well.
• Component Verification is broken.
[Treatment] • Please check and see if the object is contacting the probe well. If not, please
adjust the position of the object to contact the probe properly.
• If the error occurs when the contact is good, there is a possibility that the
Component Verification unit is broken. Please contact our technical service
dept. for information.
E690024 “Something is wrong with the measured voltage”
[Cause] The voltage gotten from the tester is irregular.
• The object(component) of the measurement is not contacting the probe well.
• Component Verification is broken.
[Treatment] • Please check and see if the object is contacting the probe well. If not, please
adjust the position of the object to contact the probe properly.
• If the error occurs when the contact is good, there is a possibility that the
Component Verification unit is broken. Please contact our technical service
dept. for information.
E690025 “Something is wrong with the measured resistance(unit)”
[Cause] The unit for the resistance gotten from the tester is irregular.
• The object(component) of the measurement is not contacting the probe well.
• Component Verification is broken.
[Treatment] • Please check and see if the object is contacting the probe well. If not, please
adjust the position of the object to contact the probe properly.
• If the error occurs when the contact is good, there is a possibility that the
Component Verification unit is broken. Please contact our technical service
dept. for information.
E690026 “Something is wrong with the measured volume(unit)”
[Cause] The unit for the condenser capacity gotten from the tester is irregular.
• The object(component) of the measurement is not contacting the probe well.
• Component Verification is broken.
[Treatment] • Please check and see if the object is contacting the probe well. If not, please
adjust the position of the object to contact the probe properly.
• If the error occurs when the contact is good, there is a possibility that the
Component Verification unit is broken. Please contact our technical service
dept. for information.
E690027 “Something is wrong with the measured voltage(unit)”
[Cause] The unit for the condenser capacity gotten from the tester is irregular.
• The object(component) of the measurement is not contacting the probe well.
• Component Verification is broken.
[Treatment] • Please check and see if the object is contacting the probe well. If not, please
adjust the position of the object to contact the probe properly.
• If the error occurs when the contact is good, there is a possibility that the
Component Verification unit is broken. Please contact our technical service
dept. for information.
250
E690028 “Resistance can no be measured. Please check if probe shuts
down properly”
[Cause] The tester overflowed data when measuring the resistance.
• The object(component) of the measurement is not contacting the probe.
• The contact between the object(component) of the measurement and the
probe is not good.
• The resistance of the object(component) of the measurement is exceeding the
measurement range.
• The Component Verification is broken.
[Treatment] • Please check and see if the object is contacting the probe well. If not, please
adjust the position of the object to contact the probe properly.
• Please check the object.
• If the error occurs when the contact is good, there is a possibility that the
Component Verification unit is broken. Please contact our technical service
dept. for information.
E690029 “Volume can not be measured. Please check if probe shuts down
properly”
[Cause] The tester overflowed data when measuring the condenser capacity.
• The object(component) of the measurement is not contacting the probe.
• The contact between the object(component) of the measurement and the
probe is not good.
• The resistance of the object(component) of the measurement is exceeding the
measurement range.
• The Component Verification is broken.
[Treatment] • Please check and see if the object is contacting the probe well. If not, please
adjust the position of the object to contact the probe properly.
• Please check the object.
• If the error occurs when the contact is good, there is a possibility that the
Component Verification unit is broken. Please contact our technical service
dept. for information.
E690030 “Voltage can not be measured. Please check if probe shuts down
properly”
[Cause] The tester overflowed data when measuring the diode polarity.
• The object(component) of the measurement is not contacting the probe.
• The contact between the object(component) of the measurement and the
probe is not good.
• The resistance of the object(component) of the measurement is exceeding the
measurement range.
• The Component Verification is broken.
[Treatment] • Please check and see if the object is contacting the probe well. If not, please
adjust the position of the object to contact the probe properly.
• Please check the object.
• If the error occurs when the contact is good, there is a possibility that the
Component Verification unit is broken. Please contact our technical service
dept. for information.
E691001 “Input/Output buffer status of CCL-48M does not get ready”
[Cause] The input/output buffer status of the backup table counter(CCL-48M) does not get
ready.
• Backup table counter is broken.
[Treatment] • Please turn off the power supply and re-boot your machine.
• If the error occurs even after the re-boot, there is a possibility that the Safety
board is broken. Please contact our technical service dept. for information.
251
E691002 “Writing-in buffer of flush memory does not get useable”
[Cause] ‘Writing-in’ buffer did not get useable when checking its status after a ‘writing-in’
command to flush memory was issued.
• Flush memory is broken.
[Treatment] • Please turn off the power supply and re-boot your machine.
• If the error occurs even after the re-boot, there is a possibility that the Safety
board is broken. Please contact our technical service dept. for information.
E691003 “Deleting cue of flush memory does not get useable”
[Cause] ‘Deleting’ cue did not get useable when checking its status after a ‘deleting’
command to flush memory was issued.
• Flush memory is broken.
[Treatment] • Please turn off the power supply and re-boot your machine.
• If the error occurs even after the re-boot, there is a possibility that the Safety
board is broken. Please contact our technical service dept. for information.
E691004 “WSM(Write State Machine) of flush memory does not get ready”
[Cause] ‘WSM’ did not get ready when checking its status after a command to flush
memory was issued.
• Flush memory is broken.
[Treatment] • Please turn off the power supply and re-boot your machine.
• If the error occurs even after the re-boot, there is a possibility that the Safety
board is broken. Please contact our technical service dept. for information.
E691005 “Write-in voltage range error occurred in flush memory control”
[Cause] An error occurred while checking the ‘Write-in’ voltage status after a command to
flush memory was issued.
The process was aborted since the ‘write-in’ voltage is too low.
• Flush memory is broken.
[Treatment] • Please turn off the power supply and re-boot your machine.
• If the error occurs even after the re-boot, there is a possibility that the Safety
board is broken. Please contact our technical service dept. for information.
E691006 “Write-in error occurred in flush memory control”
[Cause] An error occurred while checking the ‘device protecting’ status after a command
to flush memory was issued.
The process was aborted since the master lock bit, block lock bit, and RP# lock
were detected.
• Flush memory is broken.
[Treatment] • Please turn off the power supply and re-boot your machine.
• If the error occurs even after the re-boot, there is a possibility that the Safety
board is broken. Please contact our technical service dept. for information.
E691007 “Write-in error occurred in flush memory control”
[Cause] An error occurred while checking the ‘Write-in’ status after a command to flush
memory was issued.
An error occurred while writing data in.
• Flush memory is broken.
[Treatment] • Please turn off the power supply and re-boot your machine.
• If the error occurs even after the re-boot, there is a possibility that the Safety
board is broken. Please contact our technical service dept. for information.