KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第229页
4 – 122 4.8.2.3. 2 Dual tray server (DT S) W hen y ou select "DT S", t he following screen is displayed. − The paramet ers "Pack " and "Tray Feeder" set as Component dat a appear here: you c…
4 – 121
④ X1, Y1, Z, X2, Y2, X3, Y3
These coordinates specify the component pick-up position on three corners of
a tray.
When you enter the "Sply" parameter, the component pick-up position is
automatically calculated, then displayed based on Component data.
Once a value is entered to each coordinate parameter, you can change each
coordinate separately (by teaching also).
CAUTION
To avoid a risk of injury, do not place your hand in the machine, nor
move your face or head close to the machine while the machine is
performing teaching operation.
CAUTION
If the bank is never recognized (since the machine zeroes, or the bank
moves down then up), it may be recognized automatically before the
machine moves to the pick position. Since the head moves across the
feeder while the feeder bank is being recognized, do not place your
hand in the machine, nor move your face or head to the machine.
Especially, take care when the feeder bank is recognized not from the
menu but during teaching or tracking a pick position.
Figure 4.8.2.3.1.2 Pick-up coordinates on a tray holder
If you are to teach the coordinates
When the cursor is located at the cell X1 or Y1, you can enter the coordinates X1 and
Y1.When the cursor is located at the cell X2 or Y2, you can enter the coordinates X2 and
Y2.When the cursor is located at the cell X3 or Y3, you can enter the coordinates X3 and
Y3.When the cursor is located at the cell Z, you can enter the coordinate "Z".
⑤ Used
See the description of the parameter "Used" for a tape feeder.
PWB
(
X1
,
Y1
)
(
X2
,
Y2
)
Feeding
direction
(
X3
,
Y3
)
Side
4 – 122
4.8.2.3.2 Dual tray server (DTS)
When you select "DTS", the following screen is displayed.
− The parameters "Pack" and "Tray Feeder" set as Component data appear
here: you cannot change any of them. To change either one, change the
setting of Component data.
① Sply (Supply)
Specify whether a tray is automatically selected or set on the rear side.
The Optimization utility automatically assigns trays to the machine.
Trays are assigned to the rear side.
• When you select "Automatic selection", the Optimization utility automatically
assigns trays to the machine, so you do not have to enter any data to other
items.
• When the Optimization utility is executed, items at which an asterisk mark
"*" is displayed (excluding the parameter "Lane") are automatically set.
• When you select "Rear", you can enter data to items at which an asterisk
mark is displayed (excluding the parameter "Lane").
① Angl (Angle)
See the description of the parameter "Angl" for a tape/bulk feeder.
② Pos (Position)
Specify the feeder mounting hole number which is indicated with the DTS
mounting marker.
Number of occupied feeder mounting holes 48
4 – 123
④ Lane
In case of a DTS, specify the level on which tray components are stored.
The component pick-up position on the DTS is calculated, then displayed
based on the tray specifications of Component data.
First level
Second level
●
The top level of the DTS is handled as the "first level", and the
bottom level is as the "second level".
⑤ X1, Y1, Z, X2, Y2, X3, Y3
When the parameters "Sply" and "Lane" are set, the component pick-up
position is automatically calculated, then displayed based on the tray
specifications of Component data.
Once a value is entered to each coordinate, you can change the value
separately (by teaching also).
CAUTION
To avoid a risk of injury, do not place your hand in the machine, nor
move your face or head close to the machine while the machine is
performing teaching operation.
CAUTION
If the bank is never recognized (since the machine zeroes, or the bank
moves down then up), it may be recognized automatically before the
machine moves to the pick position. Since the head moves across the
feeder while the feeder bank is being recognized, do not place your
hand in the machine, nor move your face or head to the machine.
Especially, take care when the feeder bank is recognized not from the
menu but during teaching or tracking a pick position.
⑥ Used
See the description of the "Used" parameter for a tape/bulk feeder.