KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第469页
6 − 93 1). W hen the radio butt on “Load a new PW B” is selected T he system displays the condition of the PW B transport pat h detected by the stop sensor on the screen as t he station that is to eject a board. There is…
6 − 92
− When you select the radio button “Load a new PWB”, the system ejects a board if
any board is located on the PWB transport path, and produces a PWB after
loading a board at start of production.
− When you select the radio button “Re-clamp current PWB”, the system clamps a
board located on the PWB transport path, and starts PWB production without
loading any board at start of production.
− Depending on whether there is a board on the PWB transport path, or whether the
system obtains the PWB transport path information when the current production
was interrupted, you may not be able to perform PWB production on the
“Production resume” dialog box as shown below:
Table 6.4.14.1 List of production possibilities
Choice of the radio button
Whether to
continue the
production
Whether a board is
located on the PWB
transport path
PWB transport path
information obtained when
production was interrupted
“Load a new PWB”
(Production after a board is
loaded)
“Re-clamp current PWB”
(Production after a board is
clamped)
Yes
A board is located.
No board is located.
No information
Not visible
Visible
Visible
Visible
Yes
Note
A board is located.
No board is located.
No information
Visible
Visible
Visible
Visible
Yes
A board is located.
No board is located.
No information
Visible
Visible
Visible
Visible
No
Note
A board is located.
No board is located.
No information
Visible
Visible
Not visible (None)
Visible
Yes
A board is located.
No board is located.
No information
Not visible (None)
Visible
Visible
Visible
Not visible (None)
Visible
There is no
continuous
production
file.
Note
A board is located.
No board is located.
No information
Visible
Visible
Visible
Visible
Not visible (None)
Visible
Note: Not visible if the system starts new production, while visible if the system
resumes production.
③ Condition of the PWB transport path
The “Processing before production begins” dialog box displays the condition of
the PWB transport path regardless of whether there is a continuous production file
or not as shown below:
Figure 6.4.14.1.3 “Processing before production begins” dialog box (Condition of
the PWB transport path)
− The stop sensor detects whether there is a board on the PWB transport path.
• When “ON” appears on the screen, there is a board on the PWB transport path.
• When “OFF” appears on the screen, there is no board on the PWB transport path.
6 − 93
1). When the radio button “Load a new PWB” is selected
The system displays the condition of the PWB transport path detected by the stop
sensor on the screen as the station that is to eject a board.
There is no board on the PWB transport path.
A board is to be ejected from the PWB transport path.
Although a board was detected on the PWB transport path while
production was being interrupted, the system has to eject it since
all of the necessary components are already placed on the
board.
A board is to be ejected from the PWB transport path.
However, some component(s) may not be placed on the board
or may be placed at a wrong position. Be careful to eject the
board.
−
If you click this image, the system moves a board located on the center station
to a position where the system can re-clamp it.
2). When the radio button “Re-clamp current PWB” is selected
The system displays the condition of the PWB transport path detected by the stop
sensor on the screen as the station that is to clamp the board again. Or, if the
system has the information on the PWB transport path obtained when the
previous production was interrupted (that is, if you have not loaded a production
file and not quitted the “Production” screen before resuming the production after
interrupting it), it displays the same condition of the PWB transport path as the
previous condition on the screen when it clamps a board.
There is no board on the PWB transport path.
The system clamps a board on the PWB transport path again.
The system clamps a board on the PWB transport path again.
However, some component(s) may not be placed on a board or
placed at a wrong position of a board. Be careful to clamp a
board again.
The system re-clamps a board that was located on the PWB
transport path when production was interrupted. However,
there is no board on the PWB transport path
−
If you click this image, the system moves a board located on the center station
to a position where the system can re-clamp it.
6 − 94
④ Operation information displayed when the system ejects a board or clamps it
again
The system displays the various notes on your selection of the radio button “Load
a new PWB” or “Produce after re-clamp.” and actual operation to be performed
depending on the continuous production information and the condition of the PWB
transport path.
Figure 6.4.14.1.4 Operation information when you are to eject a board or clamp it
again