KE2010.Instruction Manual.Ver.2.01,Rev.08 - 第7页
IV Greasing 1. Regarding gr easing, use Albania G rease. 2. To prevent the occur rence of an inflam mation or r ash, immediat ely wash the related port ions if g rease adheres to your eyes or other parts of your body. 3.…
III
To turn off power supply means to turn off
a power supply switch and then to draw out
a power plug from a receptacle or to
separate the power cable from the supply
side.
Hereinafter the same.
Situations in Which It Is Necessary to Turn Off Power Supply
1. In the case of an abnormality or an accident, or in the event of power failure,
immediately turn off power supply.
2. In order to prevent accidents due to unintended start-up of the machine, carry out
inspection, repair, or cleaning of the machine only after turning off power supply.
3. When drawing out the power supply plug, do it by holding the plug itself, not the
cord.
Matters of Caution at Each of Its Use Stages
Transport
1. When lifting the machine or moving it, take sufficient safety measures so that no
dropping accidents will occur.
Unpacking
1. Read all instructions shown on the transport-use container.
2. Never cut tapes with a cutter.
3. Retain delivery-use materials.
Installation
1. To prevent the occurrence of any accident due to unintended moving of the
machine in operation, make casters float using a height adjuster.
2. Install this machine at a flat position.
3. To prevent the occurrence of electric shock, power leakage, or fires, use attached
products regarding cables, and link them to the specified positions.
4. To prevent electric shock, power leakage, or fires, make sure that irrational force
will be applied to the cables while the machine is in operation.
5. Securely fix the power supply plug and the connector of an I/F cable. When
drawing out the power supply plug or the I/F cable, do it by holding the connector
unit.
Before Operation
1. To prevent accidents to human bodies, make sure before supplying power that
there is no damage, coming off of parts, or loosening of connectors and cables.
2. To prevent bodily accidents, never put in your hand into the driving unit.
CAUTION
IV
Greasing
1. Regarding greasing, use Albania Grease.
2. To prevent the occurrence of an inflammation or rash, immediately wash the
related portions if grease adheres to your eyes or other parts of your body.
3. If grease is mistakenly swallowed, immediately consult a physician to prevent
diarrhea or vomiting.
Maintenance
1. To prevent accidents due to unaccustomedness, repair and adjustment shall be
conducted by maintenance engineers who are versed in the machine. In
replacing parts, use genuine parts of our company. We will not assume any
responsibility for an accident due to the use of non-genuine parts.
2. To prevent accidents or electric shock due to unaccustomedness, entrust
electrical repair or maintenance work (including wiring work) to persons versed in
electricity, or ask engineers of our company or its sales company to do it.
3. To prevent accidents due to unintended start-up of the machine, conduct repair or
adjustment only after removing air supply pipes and discharging residual air.
4. To prevent bodily accidents, confirm after such work as repair, adjustment, or
parts replacement that no screws or nuts are loosened.
Use Environment
1. Use the machine in the environment free from effects of noise sources (magnetic
waves), such as high-frequency welders, in order to prevent accidents due to
erroneous actions.
2. In order to prevent accidents due to erroneous actions, use the machine in the
environment where source voltage surpasses 200V (220V, 240V)± 10%.
3. In order to prevent accidents due to erroneous actions, do not use the machine in
the environment where the supplied air pressure is 0.5 to 1.0MPa.
4. To ensure safety, use the machine under the following environment:
Ambient temperature during operation + 10C - +35C
Relative humidity during operation 50% or less (35C)
90% or less (20C)
5. To prevent accidents due to breakdown of electric/electronic parts, turn on power
supply sufficiently after the fear of dew condensation is eliminated, because such
condensation may occur when the machine is rapidly moved from a cold place to a
warm location.
6. To prevent accidents due to breakdown of electric/electronic parts, stop the use of
the machine during lightning, and draw out the power supply plug.
CAUTION
V
Where to stick warning labels
[Front]
[Rear]
Moving parts
warning label
"Take care not to be
caught in the machine"
warning label
Moving parts
warning label
"Take care not to be
caught in the machine"
warning label
High voltage
warning labels
High voltage
warning labels
Moving parts
warning label
High voltage
warning labels
Moving parts
warning label